0
Yes but you will not get the full watt rating out of the tank. Watts = amps x volts. Say the tank draws 20 amps. 20A x 240V = 4800 watts. 20A x 208V = 4160 watts. It will take longer to heat your water with less wattage.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Can you run a 110v heater on 220v circuit?
No.It'll overload and fail just about immediately.It's possible - but not recommended - to run two 110 v heaters in series from a 220v circuit.
What is average 208-230 voltage?
208V is one standard in the US for light commercial 3-phase power. It measures 208V phase to phase and 120V phase to neutral. 230 (or 240)V refers (in the US) to the common service supplied to residential. It is single-phase, with two hots and a neutral; 120-0-120. One hot and the neutral (120V) is used for receptacles and small appliances, both hots (240V) are used for large appliances, such as stoves, ovens, air conditioning, and water heater.
Is there a switch available to control power to a thermostat for 20A 240V electric baseboard heater?
There are two types of thermostats. One is a line voltage stat. This is in effect a switch and when turned to the off position the voltage is interrupted and the heater will not operate. The other type of stat is low voltage. There will be a relay in the baseboard heater that the thermostat is connected to. With this type if installation to turn the power completely off you will have to turn the breaker off that feeds the circuit.
What are the averag volts used in a US Home?
US homes use a 240 volt single phase 'Edison' system. It is a 3-wire (4 with the ground) system. Phase to phase measures 240v, while each phase to neutral measures 120v.
Sequencer in forced air electric furnace is activated by?
when the wall thermostat closes a contact (at the set temperature), 24 volts is passed through a concave metal disk in the sequencer. The current heats the disk expanding the metal till it pops to a convex position pushing a plastic insulator rod, attached to a metal bar that closes the 208v or 240v circuit activating one of the heating elements or furnaces fan
How do we know when to connect to 208v or 240v?
Its on the specifications of the device you will plug
What is the number of AMPS for a 240V 2400 watt water heater?
Watts = Amps x Volts for a resistive load like a water heater.
Can you use one wire from the panel with 240v on it to wire a 240v water heater?
In North America it takes two "hot" wires to obtain 240 volts.
Can you run a 110v heater on 220v circuit?
No.It'll overload and fail just about immediately.It's possible - but not recommended - to run two 110 v heaters in series from a 220v circuit.
What is average 208-230 voltage?
208V is one standard in the US for light commercial 3-phase power. It measures 208V phase to phase and 120V phase to neutral. 230 (or 240)V refers (in the US) to the common service supplied to residential. It is single-phase, with two hots and a neutral; 120-0-120. One hot and the neutral (120V) is used for receptacles and small appliances, both hots (240V) are used for large appliances, such as stoves, ovens, air conditioning, and water heater.
What is average 208 230 voltage?
208V is one standard in the US for light commercial 3-phase power. It measures 208V phase to phase and 120V phase to neutral. 230 (or 240)V refers (in the US) to the common service supplied to residential. It is single-phase, with two hots and a neutral; 120-0-120. One hot and the neutral (120V) is used for receptacles and small appliances, both hots (240V) are used for large appliances, such as stoves, ovens, air conditioning, and water heater.
How many volts does a freezer use?
A typical freezer will use around 115-120 volts. It's important to check the specifications of your specific freezer to ensure the correct voltage requirements.
How many amps are generated by a 1500 watt heater at 208 volts?
You have to be careful here. A heater will be advertised as "X" watts, but that is only true if you connect it to the voltage source it is supposed to be connected to. If you plug it into a higher or lower voltage source than intended, it will produce a different number of watts.Electric heaters are just resistors. When you run electricity through them, they get hot. If you run more electricity through that resistor, it will produce more heat. If you run less electricity through it, it will produce less heat.As an example, you can find "1500W/120V" water heater elements at the hardware store. This means that if you plug it into a 120V source, it will produce 1500W of heat, and it will pull 1500W/120V = 12.5A of current.You can calculate the resistance of the heater by taking voltage times voltage divided by watts, so this "1500W/120V" heater is really just a resistor of this many Ohms:120V * 120V / 1500W = 9.6 OhmThat Ohm value is physical property of the device. It will not change. If you were to take this heater now and plug it into a 240V supply, you can calculate the amps with voltage divided by resistance:240V / 9.6 Ohm = 25 AmpsAnd, for watts, you can take voltage times voltage divided by ohms:240V * 240V / 9.6 Ohm = 6000WSorry for the long text, but it's crucial that you understand this.If your heater is 1500W and is INTENDED to be running on 240V, you have a 38.4 Ohm resistor. Running that resistor at the lower 208V will produce only 1126W of heat and will pull just 5.4 Amps of current.However, if your heater is 1500W and is indented to be running on 120V, then you have a 9.6 Ohm resistor. You will almost certainly start a fire if you plug it into a 208V supply, because you will be pulling close to 22 Amps and producing 4500W of heat.
You are building a new house and trying to decide between 120v and 240v which is better More practical?
In the US, both 120v and 240v will be needed for your home, as different appliances need different voltages. Your TV needs 120V, while your electric dryer and stove will need a 120V/240V supply. If you have an electric water heater, or central AC unit, they will need a 240V supply.
What is low voltage transmission?
In the supply industry it refers to circuits of below 1000 volts. Common voltages used are 120v, 208v, 230v, 240v, 277v, 400v, 415v, 480v.
IS there an adapter for a 240V heater that will allow you to plug it into two 110V outlets?
No. Sounds like a fairly hazardous thing to try as well. If it's to use a heater in the US, then buy a US heater at a lower cost than any adaptor that might do the job for you. If it's to use on a UK building site that has 110V but doesn't have 240V, it breaks all the rules because you end up with 240V where you shouldn't.
How do you change a heater from 120 volts 3a to 240 volts 1.5 a?
the simplest solution is by connecting two 120v 3amps heater in series , the same can be used directly on 240v. However the current drawn will still be 3 amps & Not 1.5 amps. The heater output power will be double that of a single heater running on 120v. ( or equvalent to two heaters operating on 120v. supply ) A more expensive method is to use a stepdown transformer which can be powered on 240v & connect the heater on the transformer 120v side. this method will consume approx. 1.5 amps from the 240v supply.
