0
If you mean can you split off the power from an outlet to another outlet or device the answer is yes. Just make sure not to overload the circuit. Usually outlets have two connection points for Hot (Copper colored screw) - black wire and Neutral (Silver colored screw) - White wire. Just take off power at the unused screws if they exist or use wire nuts to branch off other wire pair and a pigtail to reconnect to the outlet if two pairs of wire already on outlet
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is use of neutral in a wall receptacle?
The neutral in a receptacle is the return conductor to complete the circuit back to the distribution panel. When a device is plugged into the receptacle this completes the circuit and allows the current to flow and the device to operate.
Is a 110 volt electric receptacle the same as 120 volt receptacle?
Yes, the rating on the receptacle is the maximum amount of voltage that is legally allowed to be applied to the device.
How do you use receptacle in a sentence?
we used a receptacle to hold the cookies.
Can you install a 277 volt receptacle in place of a 240 volt receptacle?
No. To prevent this sort of thing from happening, the 277 volt device and receptacle is physically larger that a 240 volt receptacle and will not fit in a regular receptacle junction box. For a 277 volt system the proper size junction boxes have to be purchased.
How many volts come out of a average outlet?
Voltage does not come out of an average home outlet under normal circumstances.In North America the common potential voltage is 120 volts and is always at the receptacle as long as the circuit is energized. When an electrical device is plugged into the receptacle, through the device's connected cord, this brings the potential supply voltage to the electrical device.When the device is turned on a current (amperage) will flow, governed by the resistance of the device. If it is a lamp, it will become bright. If it is a radio you will hear sounds.When you unplug the electrical device from the receptacle, the device will stop operating but the voltage potential will still remain on the "hot" side of the receptacle's blade contact point.
Can you put a 120 v receptacle on a 240 v circuit breaker?
No, the electrical insulation rating of a 15 amp duplex receptacle is only rated at 130 volts. The 15 amp 240 volt receptacle is rated at 250 volts. The 240 volt receptacle also has a tandem pin configuration instead of the parallel configuration of the 120 volt device. The different pin configuration is so that a 120 volt electrical device can not be plugged into a 240 voltage receptacle.
Do I need GFCI breakers for 30 amp 240 volt receptacle in a commercial kitchen?
Usually no. Not unless the receptacle is in the vicinity of standing water. This is to protect the person that has to disconnect the plugged in device from the receptacle, while standing in the adjacent water.
Can a 110 volt device be plugged into a 125 volt outlet?
Yes, a 110 volt device can be plugged into a 125 volt receptacle. The voltage rating on the receptacle is only there as the highest voltage supply that the manufacturer recommends their equipment be connected to.
Is there an adapter for a NEMA 14-30 plug and a NEMA 10-30 receptacle?
A NEMA 14-30 is a 3 pole 4 wire grounding receptacle rated at 30 amps 125/250 volts. A NEMA 10-30 is a 3 pole, 3 wire non grounding receptacle rated at 30 amps 125/250 volt.As the NEMA 10 device has no ground terminal on it, it is not a standard receptacle device so no adapter is made for it.
Why would someone use two positive wires to complete a house 2 plug receptacle circuit?
If the 2 hot wires are connected to either side of a receptacle, you have a 240v receptacle (assuming it's in the US). This is typically done for window air conditioners. But code requires that the receptacle have a different configuration than other receptacles in the building so you don't run the risk of plugging in a 120v device into a 240v receptacle.
EXPLAIN WHAT WIRES DO IN A RECEPTACLE?
Wires bring the voltage source to the junction box of the receptacle. At this point they are terminated under the screws of the receptacle. With the receptacle screwed to the junction box and the cover plate installed the outlet is ready to be used. The last thing to do is turn the breaker back on to energize the receptacle.
What if a 110 outlet reads 125 volts?
This will cause no problem to any of the connected equipment. If you read the specifications on the side of a receptacle you will find that the rating of the receptacle is usually 125 to 130 volts depending on the manufacturer of the device.
