It seems like you are describing the Red, Black, White and Ground in your electric panel. There is 240 VAC between Black and Red and 120 VAC between Black and White and 120 VAC between Red and White. The electric panel has two busses that supply 120 VAC on alternating breakers in your panel. Essentially, the Red turns into "black" in the panel for all practical purposes. If you have a 240 VAC circuit it essentially takes up to two vertical positions in your electric panel.
To answer this question fully the type of appliance has to be stated and its voltage.
You don't say "turn off" or turn on". Light should be connected black to black and white to white and ground to ground. If you connect white to ground it will work, but you are then using the ground wire for an unintended purpose. Neutral is bonded to Ground at the panel. Current on ground wire could cause ground loops and may cause GFCI to trip if you have them in your house.
There should be two wires in the box, black and white and possibly a bare one depending on the age of the wiring in the house. The fixture has two screws on the base. One wire goes on each screw. If there are short wires on the fixture, black to black and white to white. If there is a bare ground wire in the house box, it attaches to the body of the fixture. If there is no ground screw on the fixture, do not worry about it.
If the cable you are trying to connect the dryer up to only has a white, black and ground wire, then the dryer is not going to work. The cable needs to be a three wire, the ground wire is never counted when discussing house wiring. Open up the electrical access panel on the back of the dryer. You will see a terminal block. A red and black and white connect to this terminal strip. The "hot" wires are connected to the outside terminals. The neutral (white) wire will be in the center. Connect the ground wire to the frame of the dryer. It is very important that this ground wire be connected as this is the wire that carries the fault current to trip the breaker should a fault arise.
You will have to check to make sure. Normally, with 4 wires, the black and red are both power for 220. White for neutral and bare for ground. If you are only using one leg of it, you would use the black, white, bare ones and cap the red one. Someone may have used the 4 strand because they had it or 220 was planned but not done or both the red and black are hot. You should be able to tell in the panel. Do the red and black both connect to separate breakers or to one or is the red not connected?
To answer this question fully the type of appliance has to be stated and its voltage.
A basement of a house is the room or space that is below ground level. A basement appliance that can heat your house is a furnace.
You don't say "turn off" or turn on". Light should be connected black to black and white to white and ground to ground. If you connect white to ground it will work, but you are then using the ground wire for an unintended purpose. Neutral is bonded to Ground at the panel. Current on ground wire could cause ground loops and may cause GFCI to trip if you have them in your house.
If you're asking whether you have to connect the fixture ground to the house ground, you do. The idea is to connect any exposed portion of a metal fixture to ground, keeping anything you would be able to touch from having a hazardous potential on it. The way to do this is to connect the fixture ground (which is connected to the metal chassis) to the building ground (which comes from your electrical panel).
Throw it on the ground. That should teach him.
There should be two wires in the box, black and white and possibly a bare one depending on the age of the wiring in the house. The fixture has two screws on the base. One wire goes on each screw. If there are short wires on the fixture, black to black and white to white. If there is a bare ground wire in the house box, it attaches to the body of the fixture. If there is no ground screw on the fixture, do not worry about it.
If the cable you are trying to connect the dryer up to only has a white, black and ground wire, then the dryer is not going to work. The cable needs to be a three wire, the ground wire is never counted when discussing house wiring. Open up the electrical access panel on the back of the dryer. You will see a terminal block. A red and black and white connect to this terminal strip. The "hot" wires are connected to the outside terminals. The neutral (white) wire will be in the center. Connect the ground wire to the frame of the dryer. It is very important that this ground wire be connected as this is the wire that carries the fault current to trip the breaker should a fault arise.
No. If the service is missing a ground wire the electrical inspector will not pass the installation. With out the inspectors approval the utility company will not connect the house and turn the power on.
That depends if it is automotive or household wiring. On a car a black wire is almost always ground. On house wiring black is the supply (hot) wire.That depends if it is automotive or household wiring. On a car a black wire is almost always ground. On house wiring black is the supply (hot) wire.
You will have to check to make sure. Normally, with 4 wires, the black and red are both power for 220. White for neutral and bare for ground. If you are only using one leg of it, you would use the black, white, bare ones and cap the red one. Someone may have used the 4 strand because they had it or 220 was planned but not done or both the red and black are hot. You should be able to tell in the panel. Do the red and black both connect to separate breakers or to one or is the red not connected?
There are typically 8 to 10 receptacles on most house circuits with special applications in Kitchens. The wires are in parallel with Black to Black, White to White and Bare Wire Ground to Ground.
Summit Appliance is the manufacturer of Summit Appliances. www.summitappliance.com Source: I am an in-house salesperson for Summit