0
absolutely not...
Besides the fact that "absolutely not" is the common sense answer, the NEC strictly forbids electrical panels from being in bathrooms. There are very few other restrictions, including the fact that there is no restriction on how close to water a panel can be. But the restriction on panels in bathrooms stands tall.
What else can I help you with?
What measured load can you put on an electrical panel?
If you have a measured continuous load of say 80 Amps, you would want to have a panel rated at 100 A. For continuous load you want to be at 80% of rated capacity.
Why is it good to a ground on a receptacle?
Not only is it good to put a ground on a receptacle it is mandatory by the electrical code rules. The ground is installed to provide a low impedance return to the distribution panel to trip the breaker supplying the circuit in case of a ground fault occurring on the circuit.
Can you run a 240v wire from the electrical panel then put a junction box to run it where you want?
A 240 volt wire is the insulation factor of the wire. If you mean a 240 supply source from a distribution panel to a junction box then the answer is yes. You have to keep in mind that the box has to be accessible, meaning that you can get to the box to check the splice within the box. Don't bury the junction box behind the wall board.
Can you put a breaker panel in a hall?
Yes a breaker panel can be located in a hall. In fact a lot of apartments have them in that location just as you come in the main door to the apartment.
What is an electrical riser?
An electrical riser diagram (also known as a "one-line" diagram) is a drawing that shows how an electrical system is designed by diagramming how the different components are connected. It is the roadmap which electricians use as the directions to how the system is put together. You can learn more about them here.
Can you install a main electrical panel in a laundry room or furnace room?
Yes, you can install a main electrical panel in a laundry room or furnace room. However, it must meet building codes and have proper clearances. It's important to consult with a licensed electrician to ensure the installation is done safely and correctly.
What is it when you put your car into drive the instrument cluster panel wont work?
electrical issue
What do you do with CJ's flash drive after you put it in the computer?
You go out of the room into the bathroom. You go right to go yo the bathroom and you need to flush the thumb drive.
According to astrologer where you have to put your computer in a room?
If he or she has any common sense then by an electrical socket.
Where can you put a flood kit in your house?
You could put it in the attic? Right? Maybe like a safe spot, like the bathroom? or like your room, or in the garage.
What measured load can you put on an electrical panel?
If you have a measured continuous load of say 80 Amps, you would want to have a panel rated at 100 A. For continuous load you want to be at 80% of rated capacity.
Where do you put the sarcophagus on the SIMS 2 Nintendo DS game?
In the managers room, that your sim uses, with the control panel thing in
Is it legal to put a spybot in a bathroom?
If the bathroom in question is in your home, yes.
In which room in a house might one put a Pegasus faucet?
A Pegasus faucet may be a good place to put in bathroom or kitchen sinks. This faucet is a great home decoration cause it has such an elegant look to it.
I work in a franchise fast food chain and I'm wondering whether it is legal to put audio surveillance in the back room?
(in the US) As long as the surveillance cameras are not located in the employees bathroom or locker room it IS permissible and legal.
Can you put a shower in a bathroom?
yes
How can I perform a pushmatic breaker replacement in my electrical panel?
To perform a Pushmatic breaker replacement in your electrical panel, follow these steps: Turn off the main power supply to the panel. Remove the cover of the electrical panel. Identify the Pushmatic breaker that needs to be replaced. Carefully disconnect the wires connected to the breaker. Remove the old breaker by gently pulling it out. Insert the new Pushmatic breaker into the slot. Reconnect the wires to the new breaker. Put the panel cover back on. Turn the main power supply back on and test the new breaker. Remember to always prioritize safety and consult a professional if you are unsure about any step.
