0
Change the spool of line on a weed eater SG11 Can't figure out how to get the original one off?
Wiki User
∙ 13y ago
Locate the round tap button. Pull it straight out, firmly. This opens the chamber for new line or spool. I figured this out five minutes ago.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How many syllables does the word 'spool' have?
One.
How many pieces of ribbon each 3.2cm long can be cut from a spool of ribbon 15 m long?
4.68
How many pieces of tape 2.4 dm long can be cut from a spool of tape 15 m long?
1600 pieces
What is cone thread?
Cone thread is thread typically used on an overlock "serger" machine. It is thread wound on a cardboard or plastic cone, and is much bigger than a standard thread spool.
How many pieces of string 0.62 dm long can be cut from a 21204 dm spool of string?
cheska has 147 metres of red ribbon.She cut it into 0.21 metre long. how many pieces of ribbon does she have? what is answer and solution.
How do you change the spool on a craftsman bushwacker weed eater?
I can't seem to get the spool off.
Which brand of trimmer has the fewest spool tangles?
The Weed Eater brand of trimmers have very few spool tangles
How do you change the spool on a weed eater rt112c?
You can find the User's Manual at the following web address for Poulan.Com http://72.3.225.179/manuals/545186760en_r1.pdf Hope this helps.
Do a electric weed eater have littke bb's in it?
No, electric weedeaters have a motor and a cord spool.
How do you wind new weed eater string on an old spool?
pull straight out to remove the spool, wind in the direction of the arrow - to replace, feed the string through the hole and pull on it, keeping slight tension on the spool as you push it back into the head
What if string isn't coming out of weed eater?
It's tangled on the spool. You need to open & rewind around it.
How do you get the spool off a weed eater twist n edger TE 15?
The spool can be taken off a Weed Eater Twist N Edger TE 15 by pressing inward and turning it counter clockwise. This allows more cutting line to be added or jams to be cleared.
What is the procedure for re stinging the spool on a Weed Eater Model RTE113C?
Line the mark up with the arrow and pull real hard.
How do you re string dual no bump weed eater?
it actlly all depends on which head you have...but regardless always roll spool putting the line on it, don't roll the line, but the spool, keeps the line able to come off when bumping, if you wind the line around the spool it will normally melt and prevent it from feeding.
How do you install new string on a homelite 26ss weed eater?
Installing new string on a Homelite 26ss weed eater is very easy. You will need to take off the empty spool and put the new one on. Take two pieces of the strings and put each in one of the empty slots opposite each other. The put the spool and grasp the strings pulling them into place.
How do you change string on toro weed eater?
Toro 1100 Heavy Duty Trimmer/Weeder. Insert flat blade screwdriver into one of the two window slots on spool. Twist screwdriver 1/4 turn. Spool will snap off. Hook one end of line into groove on spool allowing no more than 1/8 inch of line to protrude. Wind in the direction of arrows on spool in level rows. Wind no more than 50 feet and use up to .065" diameter string. Keep line tight on spool. Make a hook in the line when done winding and secure in groove with about three inches extra. Thread end of line through through eyelet. Spool and core are keyed. Align and and push to snap back on. Pull line free from groove in spool.
How do you change string on toro weed eater 51325?
Toro 1100 Heavy Duty Trimmer/Weeder. Insert flat blade screwdriver into one of the two window slots on spool. Twist screwdriver 1/4 turn. Spool will snap off. Hook one end of line into groove on spool allowing no more than 1/8 inch of line to protrude. Wind in the direction of arrows on spool in level rows. Wind no more than 50 feet and use up to .065" diameter string. Keep line tight on spool. Make a hook in the line when done winding and secure in groove with about three inches extra. Thread end of line through through eyelet. Spool and core are keyed. Align and and push to snap back on. Pull line free from groove in spool.
