answersLogoWhite

0


Best Answer

No, the bare copper grounding conductor can not be in a conduit with other conductors. It can be in conduit by itself to provide mechanical protection for the wire.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Does the Nec allow grounding electrode conductor to be run in conduit that has other conductors in the conduit and what code section?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Electrical Engineering

Does the metal conduit count as a ground?

No, each conduit must contain a separate grounding conductor.


Does the grounding bar hook to meterbox or breaker box?

A grounding bar is most often located in the breaker panel. This is where all your grounding conductors are landed. If the panel is your primary service panel, neutrals and grounds can both be landed there. The NEC (US) requires that all service equipment be bonded together. This includes your meterbox. To most people bonding and grounding look alike but they serve different purposes. In most cases this bonding consists of a #6 AWG solid copper conductor connecting your service panel to your meterbox and also whatever you happen to be using as a grounding electrode, usually a water pipe and ground rod. Consult a competent electrician for what is required in your area. I was on a job once where the city inspector expected this bonding conductor to be run with the service conductors inside the same conduit, which is what I would expect. But the power company for the same job required it to be run outside the conduit which is acceptable practice. Both were right, but we had to do it one way for the inspection and another way before power was supplied.


Are ground wires required in steel or aluminum flex conduits?

Yes, any flexible conduit that has live wires drawn into it must have a ground wire also installed with the "hot" conductors. The reasoning behind this rule is that the flex in the conduit is coiled and has a long length to it. The continuation of the grounding medium through the tightness of the conduit connectors to the flex was not considered a properly secured grounding system so to overcome this weakness in the grounding system, a ground wire now has to be installed.


What is the purpose of grounding electrical equipment?

It is a safety measure for devices that have a metal case where a failure in the device could cause the case to be connected to the hot side of the circuit. By grounding the case the breaker will trip instead of you getting a shock.


What size conduit for four 4 cables?

Conduit sizing is based on the number of conductors that are drawn into it. Without the number of 1000 MCM conductors, an answer an not be given.

Related questions

Does the metal conduit count as a ground?

No, each conduit must contain a separate grounding conductor.


What is the difference between a ground conductor and a ground electrode conductor?

# A ground electrode conductor is a conductor that originates at the neutral or equipment ground buses in the main service entrance panel board or separating derived system (e.g. isolation transformer) # A ground electrode is a item that is in contact with the earth (e.g. Building metal frame, underground continuous metallic water pipe etc...) # A ground conductor is a conductor that is used to keep an electrical system continuous. Ground conductors are required, by code, in all PVC conduit runs. Ground conductors are also used to keep all metallic components of the installation at the same zero potential to overcome mechanical connections that would not carry a fault current back to the supply distribution panel.


Is it permitted to use flexible conduit over 6 feet in length as a grounding means?

No. The new electrical code change does not allow any flexible conduit to be used as a ground means. It is now required to have a green ground wire pulled into the conduit with the other conductors in the flexible conduit. This grounded bonding conductor is not counted as wire fill when calculating the size of the flexible conduit to use


The calculation used to determine amperage of a conductor based on the total number of conductors in a conduit is called A derating B voltage drop C conduit fill D conductor fill?

derating


Does the grounding bar hook to meterbox or breaker box?

A grounding bar is most often located in the breaker panel. This is where all your grounding conductors are landed. If the panel is your primary service panel, neutrals and grounds can both be landed there. The NEC (US) requires that all service equipment be bonded together. This includes your meterbox. To most people bonding and grounding look alike but they serve different purposes. In most cases this bonding consists of a #6 AWG solid copper conductor connecting your service panel to your meterbox and also whatever you happen to be using as a grounding electrode, usually a water pipe and ground rod. Consult a competent electrician for what is required in your area. I was on a job once where the city inspector expected this bonding conductor to be run with the service conductors inside the same conduit, which is what I would expect. But the power company for the same job required it to be run outside the conduit which is acceptable practice. Both were right, but we had to do it one way for the inspection and another way before power was supplied.


Are ground wires required in steel or aluminum flex conduits?

Yes, any flexible conduit that has live wires drawn into it must have a ground wire also installed with the "hot" conductors. The reasoning behind this rule is that the flex in the conduit is coiled and has a long length to it. The continuation of the grounding medium through the tightness of the conduit connectors to the flex was not considered a properly secured grounding system so to overcome this weakness in the grounding system, a ground wire now has to be installed.


What is the purpose of grounding electrical equipment?

It is a safety measure for devices that have a metal case where a failure in the device could cause the case to be connected to the hot side of the circuit. By grounding the case the breaker will trip instead of you getting a shock.


What size conduit for 400amps?

The sizing of conduit systems that wire has to be pulled into is dependant on the physical size of the conductor being drawn into the conduit. The second governing factor is the conductor count of the specific conductor that is needed. A 500 MCM copper conductor with an insulation factor of 90 degrees C is rated at 430 amps. This is where the conductor count is need by the service, as to whether the service is single or three phase. In this specific case, the electrical code will allow both single and three phase installations to use the same size conduit. A maximum total of four 500 MCM conductors can be drawn into a 78 mm diameter conduit.


What is the definition of electrical capacity?

The amount of conductors per conduit size example code says 3 number 4 conductors in a 1'' conduit


What size conduit for four 4 cables?

Conduit sizing is based on the number of conductors that are drawn into it. Without the number of 1000 MCM conductors, an answer an not be given.


What is the difference between a Grounded conductor and a Grounding conductor?

In residential 120 VAC, single-phase electrical wiring, there are three main types of electrical wires: 1. Ungrounded conductor (Hot, and sometimes called "Line" or "Phase") 2. Grounded conductor (Neutral), and 3. Grounding conductor (Safety Ground or Protective Earth) The groundED conductor is the power return, intended as a current return path from the load back to the source to complete the "circuit." Its insulation is White, gray or a non-green color with white stripes. The National Electric Code requires it be connected to earth ("groundED ") at the service entrance and usually only there. The groundING conductor is usually the safety ground which serves as an emergency current return path in the event of a circuit fault or overvoltage. Like the groundED conductor, it too is grounded at the service entrance, but is also connected to metal surfaces and parts along the circuit, groundING them. It conducts current only if the current "seeks" to return to the service entrance along a path other than the Neutral (like through your chest, should a Hot wire becomes loose and contact metal in the circuit that you may touch). Since the grounding conductor doesn't normally carry current, its cross-section is sometimes smaller than the groundED conductor's. The grounding conductor's insulation is green (no other conductors can have green insulation) though sometimes it is bare copper. Sometimes the steel metal conduit enclosing the Hot and Neutral acts as the grounding conductor.


Is it permitted to use flexible metal conduit over 6 ft in length as a grounding means?

is it permitted to use flexible metal conduit over 6 ft in length as a grounding means