0
Inlet pressure/discharge pressure
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you calculate the exit pressure of a nozzle?
How to calculate the ratio of the inlet-to-exit area of the nozzle
Why is the pressure ratio higher in a centrifugal compressor than an axial compressor?
There is a substantial increase in radius across the rotating blade rows of a centrifugal compressor, which is its primary distinguishing feature from the axial-flow compressors to get higher-pressure ratio. Who says the compression ratio on a centrifugal is higher than that of a screw compressor? Unless I`m not properly understanding the question, these facts are true: a screw (axial) compressor is a positive displacement machine, meaning everything that goes into it will come out. There are no losses for re-expansion etc. A centrifugal compressor`s impeller is designed with a given amount of `lift` which is basically the difference between suction and discharge pressures or compression ratio. Exceeding the designed lift capability results in a surge where the gas momentarily goes backwards through the impeller until the excess lift condition is corrected.
What is multistage reciprocating air compressor?
A multistage reciprocating air compressor is a compressor that compresses air in a number of stages. A multi-stage reciprocating air compressor may contain 2 or many cylinders, like low pressure, medium pressure and high pressure cylinders.
What are the function of valve in gas compressor?
a gas compressor is a device that increases pressure and reduces its volume
What is the concept of a multi spool drive in a gas turbine engine?
The area available for flow along the length of the Compressors are chosen so that it decreases along the length of the compressor, due to increase in density as air gets compressed across the stages. The cross sectional area distribution across the length of the compressor is chosen for design conditions. At lower rotational speeds of the compressor, the density increase is limited as the pressure rise is very less and flow accelerates in a converging duct resulting in higher velocities in the exit. This problem is severe resulting in high machine vibration and possible component failure for a compressor designed to produce pressure ratio of over 8:1 in a single shaft. Starting the compressor (and hence the engine) becomes a problem then. To overcome this, two shaft arrangement is used so that high pressure compressor rotates at higher speeds, thereby splitting the pressure rise between the spools to alleviate this issue. High pressure compressor and Low pressure compressor are aerodynamically coupled instead of mechanical coupling. Hence HPC drives the LPC by demanding mass flow or spilling it in to bypass. Posted by Kishore C on 16th May 2013
What is jet engine engine pressure ratio?
The pressure ratio in jet engines is the ratio of pressure between the entrance of the compressor and the exit of the compressor.
What is compression ratio in air compressor?
The compression ratio is simply the ratio of the absolute stage discharge pressure to the absolute stage suction pressure.
How do you calculate the exit pressure of a nozzle?
How to calculate the ratio of the inlet-to-exit area of the nozzle
A clogged or dirty evaporator coil can?
-reduce efficiency of your unit,and increase pressure ratio of the compressor,-
How do you calculate air compressor capacity?
Flow rate times pressure divided by input will yield air compressor capacity. Input is another term for horsepower of the compressor. The pressure can be adjusted depending on how compact the result is to be.
The clearance ratio for a single stage compressor?
The ratio of clearance volume and the volume of the compressor
How do you calculate horse power of compressor?
To calculate the horse power of a compressor one would need to use the following calculation. Pump ratio x GPM @ 100 psi = CFM. For a gas compressor divide CFM by 2 and for an electric compressor, divide CFM by 4. GPM is gallons per minute and CFM is air consumption in cubic feet per minute.
How the compressor working?
Refrigerant enters the compressor inlet as a low pressure vapor. The compressor increases the pressure, and discharges it as a high pressure vapor.
How do you calculate a ratio from a percent?
Formula to calculate the ratio
Why is the pressure ratio higher in a centrifugal compressor than an axial compressor?
There is a substantial increase in radius across the rotating blade rows of a centrifugal compressor, which is its primary distinguishing feature from the axial-flow compressors to get higher-pressure ratio. Who says the compression ratio on a centrifugal is higher than that of a screw compressor? Unless I`m not properly understanding the question, these facts are true: a screw (axial) compressor is a positive displacement machine, meaning everything that goes into it will come out. There are no losses for re-expansion etc. A centrifugal compressor`s impeller is designed with a given amount of `lift` which is basically the difference between suction and discharge pressures or compression ratio. Exceeding the designed lift capability results in a surge where the gas momentarily goes backwards through the impeller until the excess lift condition is corrected.
How do you calculate surge in compressor?
fool
How do you calculate credit loss ratio?
how do we calculate credit loss ratio in banks financials
