0
Lay out or stand up the piece you're interested in.
-- Take out your tape and your calculator.
-- Measure the length of the piece, in inches.
-- Then measure the width of the piece, in inches.
-- Multiply the two numbers.
-- Divide the product by 144.
The result is now the square footage of the piece or area you measured
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the square foot of 8ft by 5 ft?
well assuming you want the board feet and assuming it is a square you would multiply 8 by 5 and get - 40 square board feet
How many square feet in a 1x6x8 foot board?
48 square feet.
How many board feet do you need to cover 300 square feet?
Depends on the size of the board.
What is the closest area of a classroom bulletin board?
2,000 square inches
How many lines of symmetry does a chess board have?
A chess board is a square, so it would have 4 lines of symmetry: two going diagonally, and 2 across the middle of the board that divide the sides in half.
How Calculate BUrsting Strength 5 Ply Corrugated Board?
To calculate the bursting strength of 5 ply corrugated board, the ability to hold weight must be tested first. The bursting strength would be the amount of weight the board can hold before breaking.
How do you convert linear footage to board footage?
Linear footage is a one dimensional measurment. Board footage is volume. one board foot is 1 inch thick by 12 inches square. 1" x 12" x 12" = 144 cubic inches of wood or one board foot.
How get square footage of drywall?
You multiply the width by the length to get square footage. Example 4x8 sheet is 32 sqare feet, 4x12 ft board has 48 square feet.
How do you calculate the compression strength of paper corrugated box?
Corrugated Board - Ring Crush Test : Ring Crush is a traditional test of linerboard and corrugating medium strength. Ring crush measures compression resistance, and this compression strength is considered to relate to the eventual compression strength of combined board made from the component. Linerboard called high strength or high performance linerboard is board that is able to achieve a specified minimum ring crush at basis weights that are lower than traditional basis weights. Corrugated Board - Concora Crush Test : The Concora Crush Tester performs a series of tests to determine the rigidity and crush resistance of corrugated material. It is used in conjunction with the Concora Liner Tester. The first test measures the flat crushing resistance of a laboratory-fluted corrugated material. The second test determines the edgewise strength, parallel to the flutes, of a short column of single-, double-, or triple-wall corrugated board. The third test evaluates the ability of corrugated material to contribute to the compression strength of a corrugated box by measuring the edgewise compression strength of a laboratory-fluted strip of corrugated material in a direction parallel to the fluted tips. Corrugated Board - Flat Crush Strength : The flat crush test is a measure of the resistance of the flutes in corrugated board to a crushing force applied to the surface of the board under prescribed conditions. Flat crush is a measure of the flute rigidity of corrugated board. A high flat crush value indicates a combination of good flute formation and at least adequate strength medium. Low flat crush may indicate a number of conditions including low strength medium, leaning flutes and crushed flutes.From: http://www.thaicorrugated.com/knowledge.php?cid=30
How do you find the square footage of the base board in a room?
Measure the length plus the width, double that number. Take that number and multiply it by the height of the base board. That will give you the number of square inches of base. Divide the number of square inches by 144 and that will give you the square feet. There are 144 square inches in each square foot.
What is conversion board feet to square feet or square feet to board feet?
you can't straight convert a linear measure to an area measure... missing info. If the board is 12" wide, then the ratio is one to one. if the board is 6" wide, the linear footage needed would be double. It's a simple ratio. width of board in inches/12 * length in feet = square feet. length in feet = square feet * 12 / width
How many board-feet of lumber for a 2000 square foot house?
A board foot is one square foot by one inch thick or 4 quarters (4/4). If you were using something thicker, then the square footage provided would be proportionately less. I.e. 8/4 lumber would yield half the square footage but would be twice as thick (2"). So, using 4/4 lumber would mean 2000 board feet for the house assuming no waste.
How do you calculate how many linear feet of bead-board to purchase?
Measure the length of each wall. Add those figures up and you get Linear footage. Divide the total linear footage by the width of the panels and round up, this is the number of planks you will need.
What are they recyled in to corrugated board?
Other paper products usually like cereal boxes
How do you improve flat crush test of paper corrugated board?
You can iron the crushed paper if you want to save it.
What is the board combination to make 71ECT corrugated cardboard?
56/23/35/23/35 it will vary depending on the board you carry, like medium can be 26.
Are there any other types of cardboard besides corrugated cardboard?
There is one i know of and that's paper board but I'm not sure about any others ^_^ Grey board
