0
On a 120/240 volt distribution system the ground wire is terminated at the point where the service neutral terminated in the distribution panel. It is usually a double lug the neutral wire connecting into one hole and the ground wire connecting into the other hole. Through this lug assembly there is a machine screw that is inserted through the lug assembly and it screws into the metallic enclosure of the distribution panel. This action bonds the metal enclosure, neutral wire and ground wire bringing the point to a common potential of zero.
Wiki User
∙ 12y ago
Wiki User
∙ 11y agoA typical home water heater at 240 volts will be protected by a two pole 30 amp breaker. Run 10 AWG wire from your electric panel to heater. Wire needs two conductors for the 240 volts and a ground. Connect either conductor to one of the power connection and the other to the other connection point. Connect ground to ground. If one of the conductors is white wrap a few inches of black electrical tape around the insulation at each end to show it is not a common wire, but hot.
Add your answer:
Earn +20 pts
A 208V water heater can te be replaced by a 240V water heater?
Yes but you will not get the full watt rating out of the tank. Watts = amps x volts. Say the tank draws 20 amps. 20A x 240V = 4800 watts. 20A x 208V = 4160 watts. It will take longer to heat your water with less wattage.
Is there a switch available to control power to a thermostat for 20A 240V electric baseboard heater?
There are two types of thermostats. One is a line voltage stat. This is in effect a switch and when turned to the off position the voltage is interrupted and the heater will not operate. The other type of stat is low voltage. There will be a relay in the baseboard heater that the thermostat is connected to. With this type if installation to turn the power completely off you will have to turn the breaker off that feeds the circuit.
Can you run a 110v heater on 220v circuit?
No.It'll overload and fail just about immediately.It's possible - but not recommended - to run two 110 v heaters in series from a 220v circuit.
What are the averag volts used in a US Home?
US homes use a 240 volt single phase 'Edison' system. It is a 3-wire (4 with the ground) system. Phase to phase measures 240v, while each phase to neutral measures 120v.
Why are you not getting 240v between the two hot wires?
Because they are "in-phase". In order to get 240v, you need two 120v Alternating Current lines that are 180° out of phase, that is, opposite phases. Only when one line is +120v and the other -120v will you see 240v between the wires.
How can you get 240V single phase power from a 240V 3 phase service Can you just connect to two poles of the 240V 3 phase service?
I'm sure this isn't what you want to hear, but you probably need to ask an electrician familiar with your service and what you want to connect. As a general answer, you can connect a 240v line to line resistive load like an electric water heater to any 240v source. If you also need the 240v to have 120v line to neutral, like a 240v electric stove that contains a 120v clock and oven light, then its possible if the 3 phase power is connected in a "high delta" configuration, and you connect to the correct leads. If you have a high delta service and want to ignore the 3-phase power service and wire most or all of the loads in the building as a single phase load, the utility may have to be consulted.
You are building a new house and trying to decide between 120v and 240v which is better More practical?
In the US, both 120v and 240v will be needed for your home, as different appliances need different voltages. Your TV needs 120V, while your electric dryer and stove will need a 120V/240V supply. If you have an electric water heater, or central AC unit, they will need a 240V supply.
What is the number of AMPS for a 240V 2400 watt water heater?
Watts = Amps x Volts for a resistive load like a water heater.
Can you use one wire from the panel with 240v on it to wire a 240v water heater?
In North America it takes two "hot" wires to obtain 240 volts.
How do you change a heater from 120 volts 3a to 240 volts 1.5 a?
the simplest solution is by connecting two 120v 3amps heater in series , the same can be used directly on 240v. However the current drawn will still be 3 amps & Not 1.5 amps. The heater output power will be double that of a single heater running on 120v. ( or equvalent to two heaters operating on 120v. supply ) A more expensive method is to use a stepdown transformer which can be powered on 240v & connect the heater on the transformer 120v side. this method will consume approx. 1.5 amps from the 240v supply.
A 208V water heater can te be replaced by a 240V water heater?
Yes but you will not get the full watt rating out of the tank. Watts = amps x volts. Say the tank draws 20 amps. 20A x 240V = 4800 watts. 20A x 208V = 4160 watts. It will take longer to heat your water with less wattage.
What voltage is needed for electric ovens?
240V
How do we know when to connect to 208v or 240v?
Its on the specifications of the device you will plug
IS there an adapter for a 240V heater that will allow you to plug it into two 110V outlets?
No. Sounds like a fairly hazardous thing to try as well. If it's to use a heater in the US, then buy a US heater at a lower cost than any adaptor that might do the job for you. If it's to use on a UK building site that has 110V but doesn't have 240V, it breaks all the rules because you end up with 240V where you shouldn't.
How do you connect a 240V electric cooktop with four wires to the 120V services from the electric panel which is 2 wires?
If your electrical service is only 120 volts you have a problem. There is no way that you can connect a 240 volt cook top to that service. You have two options, one is to upgrade to a new 120/240 volt electrical service. Your other option is to find a 120 volt electrical cook top.
Why wont your central air start and your lights and electronics keep flickering?
It is very possible that you have lost 1 phase to your home. This means that one of the 120 volt lines ( you have 2) coming into your home is out. This could be at the meter or at the pole/ground transformer. Some of the appliances and lights in your home will work and some will not. An AC unit requires 240v to operate. So does and Electric dryer, heat pump, electric water heater, and some electric baseboard heat. You should call an electrician or your local electric company to have the issue fixed.
You want to fit a heater in a outhouse from a domestic 240v supply the cable has a resestance of 1.5 ohms and the heater has a resistance of 28.5 ohms what is the voltage drop in the cable?
31.5
