0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the compression ratio for an engine if each cylinder has a maximum volume of 500 cubic centimeters and a minimum volume of 50 cubic centimeters?
Compression ratio is exclusive to each cylinder, though they will all have the same result if they are the same dimensionally ( and they always are) > Divide the total engine capacity by the number of cylinders, this gives the capacity or swept volume of each cylinder (bore * stroke) > So in a 2.0 (2000 cc) litre 4 cylinder engine, each cylinder has a 2000 / 4 = 500 cc swept volume (bore * stroke) > The combustion chamber is the volume remaining at top dead centre (TDC) > Compression ratio = volume at BDC (swept volume + volume at TDC) / volume at TDC
What is the volume of a cylinder with a radius of 7 and a height of 4?
Volume of cylinder= pie x 72 x 4 = pie.196 = 616 cubic units.(Taking pie= 22/7)
How do you find the height of cylinder volume cm diameters 4 cm?
Cylinder height in cm = volume/(pi*radius2)
How many cubic inches are in a cylinder that has a diameter of 4 inches and a height of 10 inches?
Volume of the cylinder = pi*22*10 = 125.664 cubic inches rounded to 3 decimal places
How do you find the radius of big cylinder given radius of small cylinder and big cylinder is 4 times larger than the small cylinder?
The answer will depend on whether the larger cylinder is 4 times larger in terms of radius, cross-sectional area, or volume. If radius, multiply the smaller radius by 4. If cross-sectional area, multiply the smaller radius by 2. If volume, you do not have enough information.
How do you set the valve lash on S10 2.8?
Cylinder 1 at TDC adjust 1,5,6 Intake 1,2,3 Exhaust Cylinder 4 at TDC adjust 4,5,6 Exhaust 2,3,4 Intake
Ignition timing on 6 cylinder 5 speed 1994 Toyota 4 runner?
10 degrees before TDC
Timing belt Honda Pilot?
when clyinder 1 is on tdc where does cylinder 4 have to be when retiming a 3.5 vortec on a 2004 pilot
What is the timing on a 95 Mitsubishi Galant 4-cylinder?
it depends on your engine: 1) 4G64/G (galant?) 3-7 before tdc 2) 4G64/L (lancer?) 2-8 before tdc
How many miles per gallon should a 1997 ford ranger get to the gallon?
for a 4 cylinder about 22 to 27 and for a 6 cylinder 19 to 22
What is the compression ratio for an engine if each cylinder has a maximum volume of 500 cubic centimeters and a minimum volume of 50 cubic centimeters?
Compression ratio is exclusive to each cylinder, though they will all have the same result if they are the same dimensionally ( and they always are) > Divide the total engine capacity by the number of cylinders, this gives the capacity or swept volume of each cylinder (bore * stroke) > So in a 2.0 (2000 cc) litre 4 cylinder engine, each cylinder has a 2000 / 4 = 500 cc swept volume (bore * stroke) > The combustion chamber is the volume remaining at top dead centre (TDC) > Compression ratio = volume at BDC (swept volume + volume at TDC) / volume at TDC
Did Chevy make a 4 cylinder camaro?
the 82 is a 4 cylinder. also the 77 convert. is 4 cylinder. hope you find what you looking for
What is the ignition timing for a 250 6 cylinder Chevrolet engine?
depending on the year 72 and prior 4 to 6 degrees before tdc after 10 degrees before tdc
What is the timing gear setting for 1994 Isuzu pickup Do the arrows line up or face the other way?
I'm not sure what engine you have but on the 4ze1 which is what I have in my trooper having the arrows face both up (cam gear and crank pulley) means the engine is in tdc for the number 4 cylinder. If the arrows are facing one another it is tdc for number 1 cylinder.
How do you set the timing on a Lincoln sa200 weilding mach?
Put number 4 cylinder closest to generator at tdc then turn mag by hand until #4 sparks turn mag back 1/4 turn and install
What is the firing order for a 1992 bronco with an in-line six cylinder Where is the number one plug on the distributer?
If you are referring to the 300 or 4.9 liter in-line 6, the #1 plug is the one at the front of the engine. The firing order is 1-5-3-6-2-4 Distributor rotates clockwise. If you have the plug wires removed and if the #1 plug is not labeled on the distributor cap, you will need to find Top Dead Center (TDC) on the #1 cylinder. Remove all plugs and rotate the engine by hand until you have TDC on #1 cylinder at the compression stroke. A thumb over the plug hole will tell you when you are on the compression stroke as you will feel the pressure. A long screwdriver inserted into the cylinder will tell you when you reach TDC. Once you get TDC on #1, remove the distributor cap and look inside the distributor and the rotor will be pointing at the #1 plug terminal. The next terminal going clockwise will be 5, then 3, 6, 2, and finally 4. Make sure the plug wires do not cross each other and you will be set. Good luck.
How do you find cylinder numbers for a 1995 Altima 4 cylinder?
Cylinder one is at the front of the engine (where the belts are), and you count back from there (2, 3, 4, etc.)
