answersLogoWhite

0


Best Answer

It depends on what the wires are connected to and where the power supply is located. If the switch is lighted power has to get to the switch for the light. With a lighted switch you have a hot supply side, a neutral and then the wire going to the bell. So if Black 1 and Red 1 are supply voltage you would connect Red 1 to the hot side of switch, Black 1 would go to common as would Black 2. Red 2 would go to Bell side of the switch.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you install a doorbell with four wires both having black and red wires?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you install a doorbell?

To install a doorbell, you will first have to turn off the power to the doorbell. Pull the doorbell unit away from the wall. Disconnect the wires that hold the door bell in place. You will then have to determine whether you want a wired doorbell or wireless. If you are using wireless tuck the wires back into the wall and place the wireless doorbell in place. For a hard wired doorbell, attach the wires to the door bell, push the excess wires into the wall and attach the doorbell to the wall.


Doorbell Transformer: DIY Installation?

INSTALLING A DOORBELL HAS NEVER BEEN EASIERPeople want a doorbell for visitors, and as an alert to let them know that someone is there.Installing a transformer for your doorbell can seem like an intimidating task to do yourself, but it doesn't have to be. Making sure you have the right tools, locating the necessary spots that you will need to work, and connecting everything by the running wires are all necessary steps to get this done properly. Have Access To The Necessary ToolsThere is a whole list of tools that you will need in order to ensure that you can take the proper steps to get this project done. Depending on the exact transformer you have chosen, and in order to maintain safety, you will need a power drill, the transformer itself, electrical tape, a wire stripper, pliers, a voltage tester, and several insulated screwdrivers, which can keep you from getting shocked.Locate The Chime and Junction BoxThe junction box and the chime are the most specific parts that you will need to work on when you are installing the transformer. Use the voltage tester to determine that the circuit you are on is turned off. Once you get the all clear, install the transformer onto the junction box.Running The Appropriate WiresThe first wire you will need to connect is the transformer's wires. Remove the old wires first, however. Make sure that all of the wires that you connect fit properly. There will be a black wire and a white wire coming out. Fit the black wire first, then the white. From there, run the doorbell wire the same exact way. Once you have done this, finish up by connecting both the doorbell wires and the transformer wires.


How do you install a swag kit with two wires to a light with three wires?

I am guessing that your 3 wires are black (hot), white (neutral) and bare or green wire (ground). Connect black to black, white to white and ground wire to the metal case of swag kit.


Can someone put the following in the proper sequence to form a complete circuit insulated wires switch dry cell doorbell?

Yes.


What purpose could there be for a 10V transformer buried in a closet attached to power?

Follow the secondary wires, and see where they lead. It could be a doorbell transformer. It could be an old telephone (Trimline? Princess?) power transformer - check yellow and black in that case.


The mistresss hairs are like?

black wires


Dimmer switch that has one black wire connected to the left side and two black wires connected to the right side of the switch How do you connect these wires if you want to just install a regular flip?

Check the screws next to the wires and see what color they are if they are green, black, and red then do what i say next, if not you're screwd. just connect the red/black/green wires in the holes in the flip switch and be careful not to touch the wires just the protective covering and inert them they should auto lock in there...if not just screw them in.


How do you install 220 receptacle with white black and bare wires?

Assuming the wires are the correct gauge for application and breaker you use black and white wires as hot. Put red electrical tape on each end of white wire and connect red and black to the breaker output and bare wire to ground lug in panel. At receptacle connect black and red to hot contacts and bare wire to ground lug.


What wires are which in a 1999 eclipse to install a CD player?

Go to install doctor.com they will have it


How do you install solenoid on sprinkler system?

First locate bad solenoid. Once you have found it, unscrew wife nuts and disconnect the black wires from the other wires. Then simple unscrew the solenoid... Do all this with sprinkler system off


How do install spark wires on a 1995 Mazda mx6 4ylinder?

Remove the wires one at a time so as to not get confused. Install the new ones, paying close attention to the factory routing of the wires. Very simple.


What parts are needed to fix a doorbell?

The one tool that is essential is a multimeter. No matter what kind of doorbell, a multimeter will check the voltage of all parts. Some repairs might require a wire stripper to blend wires together. Others might simply need a replacement part.