answersLogoWhite

0


Best Answer

If you already know how to put one fixture on a 3-way, just connect white-to-white and black-to-black from one light to the next. If you're changing from a single switch to the 3-way, the exact wiring will depend on whether the power comes from the breaker box to the switch or the existing fixture. I'll assume you're starting from scratch or have the power going to the fixture.

You need #15 two-wire with ground and #15 three-wire with ground romex. Run two-wire from the breaker box to the first light fixture. Pull a another two-wire from this box to switch A and a three-wire between the switches. String two-wire from the first light to the second, second to third, etc. In the first box, connect white from source to the white fixture wire and the white going to the second box; black from source to the black to switch A; and the black fixture wire to both the white to switch A and the black to the next fixture. At each of the other 5 fixtures, connect all white to white and black to black (three pair in each box except the last one). At switch A, connect the white from the fixture to the common (center) connector and the black directly to the black going to switch B. The red and white wires going to switch B are connected to the two outside connectors of switch A. At switch B, the black goes to the common connector and the red and white to the outside connectors. At each box, connect all the bare wires (second ground) to each other and to the fixture or box. Now turn the power back on. If all the connectors are tight, power should follow the black wires from source past the fixture and switch A to switch B. From there it will go through one or the other of the travellers and, if switch A is in the same position as B, up the white switch leg to the fixtures, turn on all the lights and go back to ground.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:25:21
This answer is:
User Avatar
Study guides

Physics

20 cards

What type of circuit in which all parts are connected in a single loop

What angle is between 90 and 180

What condition has symptoms that include ringing buzzing or roaring in the ears or head

What is the transfer of energy as electromagnetic waves called

โžก๏ธ
See all cards
3.67
โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…
12 Reviews

Add your answer:

Earn +20 pts
Q: How do you wire 6 recessed fixtures in succession on a 3 way switch?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Do you connect the white wire to the black wire?

In some cases in residential wiring you do. From a light fixture junction box to a switch box, the cable is a two wire, black and white. To connect the switch into the circuit at the fixture box, the "hot" conductor is connected to the white wire that goes down to the switch. The switched "hot" comes back on the black wire and this is then connected to the fixtures black wire. The white (neutral) is picked up in the fixtures junction box and connected to the fixtures white wire.


How do you add another porch light to an existing switch?

Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.


How do you wire plunger lamp holder of fluroscent light fixture?

It sounds like you are describing either a slimline or dc recessed base type of fluorescent fixture. There is a wiring diagram on the ballast of both of these types of fixtures. Do your wiring the same as what is shown and you will have no problem.


How do you wire two light fixtures?

You can wire two light fixtures several ways.One way would be to come out of a junction box with a supply feed going to each fixture.


Can you use 14 gauge wire with a 15 amp breaker for recessed lighting?

Yes.


How do you wire a series of recessed lights to a single switch when the power goes to the lights first?

The switch goes between the supply and the string of lights. If the supply is in a ceiling box you need to run a 3-wire cable from the switch to the ceiling box. Since your normal Romex cable for residential use has a black, white and bare wire you would use them as follows: At the switch connect black to one side of switch and white to other side.. Wrap black electric tape around white cable for 3 inches or so to identify it as a hot wire. Do the same at the ceiling end. In the ceiling connect one switch black wire to the supply black and the other pseudo black wire (White wire with tape) to the black wire on light fixture. Connect the supply white wire to the light white wire. Connect all bare wires together (ground). Connect bare wire at switch to green screw on switch.


Can you by pass the AC pressure switch?

If it is a 2-wire switch- yes If it is a 3-wire switch- no


How do you connect a switch where the power is at the light?

Run a wire from the light to the switch. At the light connect the black power wire to the black wire to the switch. Not wrap some black electric tape at each end of the white wire going to the switch (This indicates that the wire is potentially hot and not a common wire). At the switch connect the black wire to one side of the switch and the taped wire to the other side of the switch. Connect the ground (bare) wire to the green screw on the switch. Now at the light connect the taped white wire to the black wire feeding the light and connect all grounds together with a wirenut.


What is the cost of wiring a 1500 square foot home?

The average cost to wire a 1500 square foot home can range anywhere between $ 9,000- $12,000. Price depends mostly on number of light fixtures, recessed lights and choice of finishes. For more info visit www.albrightllc.com


Why is there a third wire for a single pole switch?

A single pole switch would have a hot wire from the source, a switch leg going to the load, and a ground wire to ground the switch for your safety.


You want to wire a switch to a 120V 1440W Popcorn Popper Plug is not polarized plus - which lead do you wire switch to?

Wire the switch to the hot/black lead.


Can a 20 amp breaker with 12 gauge wire be used for recessed lighting?

Yes. In the US at least.

People also asked