0
Buy a 3 wire cord for your dryer.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What wire do you need for a 30 amp clothes dyer?
You need a 40 amp breaker for a range. From a 40 amp breaker, standard ranges have a three conductor #8 copper wire installed, terminating in a three pole four wire grounding receptacle. NEMA number 14-50R.
Can a 3 phase 220 volt machine that usually plugs into a line with a twenty amp breaker can a thirty amp breaker be used instead?
No, you should not install a 30 amp circuit breaker to a machine which normally requires a 20 amp supply. The circuit breaker is protecting the wire to the machine. That wire is likely only rated for 20 amps, (# 12 awg). Therefore, a 30 amp breaker could allow too much current to go through the wiring to the machine and cause the wire to burn down. Replace the 3 phase 20 amp breaker with the same amperage breaker.
What gauge of wire do i need for my 220 volt 100 amp breaker?
For a 220 volt 100 amp breaker, you would typically need a wire gauge of 2/0 AWG (American Wire Gauge) or larger. It is recommended to consult with a professional electrician to ensure the proper gauge is used for your specific installation.
How do I convert existing 3 wire 220 volt 20 amp breaker wire system to 110 volt from the box to the recepticle?
Assuming there is no neutral: 1) Turn off the breaker. 2) Disconnect 1 of the 2 hot wires from the breaker and connect it to the neutral bar (Recommend phase taping the wire white :) ) Remember which wire you used as the neutral, in a home you will most likely have a black and a red. I would keep the black hot, and phase tape the red wire white. If it's not long enough you can wire nut another white wire onto it to make it reach the neutral bar. 3) Leave the breaker OFF, at the receptacle, change it to a 120 volt receptacle. Take the wire you made the neutral, and connect it to the white screw on the 120 v receptacle, and take the black to the hot. Ground to the ground screw. Make sure you phase tape the red wire at the receptacle white as well. 4) turn the breaker on 5) test the receptacle with a meter or receptacle testing device for correct wiring.
If you have 3-4 can lights 1 ceiling fan and 3 outlets what size breaker?
A 15 amp breaker protecting # 14 wire.
What wire do you need for a 30 amp clothes dyer?
You need a 40 amp breaker for a range. From a 40 amp breaker, standard ranges have a three conductor #8 copper wire installed, terminating in a three pole four wire grounding receptacle. NEMA number 14-50R.
Can a 3 phase 220 volt machine that usually plugs into a line with a twenty amp breaker can a thirty amp breaker be used instead?
No, you should not install a 30 amp circuit breaker to a machine which normally requires a 20 amp supply. The circuit breaker is protecting the wire to the machine. That wire is likely only rated for 20 amps, (# 12 awg). Therefore, a 30 amp breaker could allow too much current to go through the wiring to the machine and cause the wire to burn down. Replace the 3 phase 20 amp breaker with the same amperage breaker.
Can you use 14-3 wire on a 20amp breaker?
No. A 20 amp breaker needs 12 gauge wire.
What gauge of wire do i need for my 220 volt 100 amp breaker?
For a 220 volt 100 amp breaker, you would typically need a wire gauge of 2/0 AWG (American Wire Gauge) or larger. It is recommended to consult with a professional electrician to ensure the proper gauge is used for your specific installation.
How do I convert existing 3 wire 220 volt 20 amp breaker wire system to 110 volt from the box to the recepticle?
Assuming there is no neutral: 1) Turn off the breaker. 2) Disconnect 1 of the 2 hot wires from the breaker and connect it to the neutral bar (Recommend phase taping the wire white :) ) Remember which wire you used as the neutral, in a home you will most likely have a black and a red. I would keep the black hot, and phase tape the red wire white. If it's not long enough you can wire nut another white wire onto it to make it reach the neutral bar. 3) Leave the breaker OFF, at the receptacle, change it to a 120 volt receptacle. Take the wire you made the neutral, and connect it to the white screw on the 120 v receptacle, and take the black to the hot. Ground to the ground screw. Make sure you phase tape the red wire at the receptacle white as well. 4) turn the breaker on 5) test the receptacle with a meter or receptacle testing device for correct wiring.
How do you connect wire to a breaker?
There is 220 volts between the two poles. If you are running 2 wires (black and white) + ground then you hook black to one pole and white to the other. Put red or black electric tape on each end of the white wire and wrap around wire for 3 inches or so next to the connection so the next person will be able to see that the wire is hot and not a neutral.
If you have 3-4 can lights 1 ceiling fan and 3 outlets what size breaker?
A 15 amp breaker protecting # 14 wire.
How do you wire a 220v connection into the main panel?
I assume you mean you are wiring a 220 volt circuit. You will install a 220 volt double pole breaker of the correct size for the circuit. An example would be for an electric dryer that requires a 30 amp double pole breaker wired with 10/3 wire. You connect the Red & Black wires to the breaker. One on each screw. You now connect the White wire to the neutral bus bar in the service panel. Then connect the bare copper ground wire to the ground bus bar in the service panel. At the dryer outlet connect the black & red to the hot screws, white to the neutral, and ground to ground. They will be labeled on the back of the outlet.
Can I you use existing 8 3 wire hooked to a 30amp breaker was hooked to old electric heater to wire a heater that requires 10 2 wire its a 5000watt 240volt heater?
Yes the wire size is larger for that size breaker but will not effect the 30 amp breaker protection of that circuit.
How do I connect 6-3 wire to the breaker?
If you need to ask, you shouldn't be doing it.
Can you use 60 amp breaker for 110 V at 110 ft and what wire is best?
A breaker is based on wire size, as the breaker protects the wire and not the load. This is a voltage drop question. A #3 copper conductor will limit the voltage drop to 3% or less when supplying 60 amps for 110 feet on a 110 volt system.
What size wire for an 80 amp 220 volt circuit?
# 3 gauge
