0
How does an access point receive electrical power if it is mounted in a location that is not close to an electrical outlet?
Wiki User
∙ 13y ago
If the term "access point" means the base station in a WiFi network or wireless LAN, it depends on its design as to whether it needs to receive any power from an adjacent electrical service outlet or not.
If it requires power from an electrical service socket outlet then power must be supplied to it either:
- by using a long enough "plug-in power extension cable with socket outlet"
or
- by installing a hard-wired permanent outlet into the wall of the room that may be connected either to a suitable existing branch circuit or, as a new branch circuit from the main breaker panel in the building, by installing a separate circuit breaker and cable having the correct ampacity.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Can you box in an electrical panel in an open room?
That depends on what you mean by "box in". You must always provide access to an electrical panel.
What is the difference between a switchboard and a panelboard in an electrical system?
Panelboards are wall mounted, usually up to 1200A bus rating. Switchboard can be free stand with access from rear. Switchboard could have bus rating up to 6000A. In general switchboards are more expensive and has more features than panelboards.
What is Tapped Inductor?
A tapped inductor is a coil to which electrical access is available at more points than only the two ends. Connection points are provided at one or more points on the coil that are between the ends. Each such point is called a 'tap'.
How is your house wired?
1Plan to run all of your electrical wires from a central location in your basement. Set aside an open area where you can set up electrical panels if needed. Keep your central location near other electrical furnishings, like the fuse box.2Install conduit before you run any type of wire through your home. This tubing protects the wires in your home and also helps keep them organized and in place. You'll probably want to use a larger diameter conduit for your central vein of wiring, and then branch off with smaller sizes for individual rooms.3Set up at least one electrical outlet and one phone jack in each room. In most rooms, you'll want one electrical outlet on each wall. It's difficult and expensive to cut into drywall and install more outlets later, so you can overestimate how many you'll need.4Put some extra conduit into the ceilings and walls in each room. This preparation will make it much easier to install a multi-room audio system or additional wiring for Internet access later. Tying string off at each of the conduits makes it very easy to pull a new wire through the tubing.5Color-code your conduit and wiring so that you can keep track of what you've installed. An extensive map of your wiring can make fixing subsequent problems much easier than if you didn't know which wires were connected to which rooms.
Why are mechanical and electrical interlocks used in certain motor control circuits?
Interlocking systems are used mainly where definite operating and sequential procedures are to be followed. Applications are generally where the safety of a person working on equipment is in danger by someone inadvertently turning on the equipment and thereby inflicting injury. Another application for interlocking systems is for access control. A simple, robust system, requiring no power, can be installed disallowing access by unauthorised persons into various areas of buildings, factories, plants etcetera. The limitations of interlocks are boundless and applications for safety or other reasons exist in all areas of industry.
Where is the Location of the fuelpump on a 1990 Honda CRX?
Inside the fuel tank mounted on top. Look in the trunk or under the rear seat for an access panel. If it does not have one the fuel tank will have to be removed in order to access the pump.
Location of oil pump on 1992 Regal 3.8 liter?
Mounted on the bottom of the engine block inside the oil pan. The oil pan must be removed to access the pump.
How do you access the reverse light sensor switch in the gearbox?
It is usually a externally mounted sensor, sometimes on the linkage, sometimes attached to the gear box. For an exact location you will have to consullt the repair manual for your car
Where is a free remote access location?
If you are wondering where the free remote access location is because you are looking for a location that offers free remote access, then you can try San Diego.
How do you access DVD drive in itschool Linux?
I'm not familiar with that Linux distribution. In most distributions, you can access it if it is mounted at /media/dvd or /mnt/dvd. If it is not mounted, you may need root privileges to do so.
How do you change the third or 'high' tail light bulb on a 2002 Tahoe?
Ensure the headlamp switch is in the OFF position. Remove the upper garnish molding at the headliner. Remove the right and left side rear window garnish molding. Lower the rear of the headliner in order to access the electrical connector. Disconnect the electrical connector. Attach a short piece of wire to the high mounted stop lamp connector in order to assist the guiding of the harness through the body. Remove the high mounted stop lamp screws. Remove the high mounted stop lamp from the vehicle.
Where is the location of the 1998 Honda CR-V fuel pump?
It is physically located in the gas tank. You must gain access to it by removing the floor carpeting from the rear deck exposing the access plate. Unscrew the access plate and you should see the top fo the pump (identifiable by steel tubing and electrical connectionscoming from it).
Where is the fuel filter on a lawnmower?
The location of the fuel filter depends on where the carburetor is mounted. If the carburetor is mounted directly atop the fuel tank, the filter is located within the tank at the end of the hose that attaches to the carburetor. The carburetor has to be removed to access the fuel filter. If the carburetor is not mounted to the fuel tank and the fuel is "gravity-fed" to the carburetor, the filter is usually an in-line filter located somewhere on the fuel line between the tank and the carburetor.
Where does wireless transmit and receive signal from?
It has an access point which transmit signal to the client and receive.
Location of 1992 mitsubushi 3000gt tcm?
I have a 1993 Mitsubishi 3000gt and the TCU is located under the console / dash. It is mounted by a metal bracket to the floor pan. You will need to remove the side carpet panels and the entire front console to access the TCU.
Difference between physical access and logical access between CPU and peripherals?
A logical access assumes that the location to be read or written is contained within a linear address space, while a physical access describes the actual access to the appropriate sector, the location within the assumed linear address space must be converted into the corresponding platter, sector, and track, and the disk hardware must be instructed to access that specific location.
Can you box in an electrical panel in an open room?
That depends on what you mean by "box in". You must always provide access to an electrical panel.
