Want this question answered?
In the United States and according to the NEC, in commercial and industrial installations, you are limited to 10 receptacles on a 15 amp circuit. The size of the wire is not a determining factor. There is no limit to the number of receptacles on a circuit in a home and there may be local codes where you live that have stricter requirements.
The circuit probably tripped because too many things were plugged into the receptacles or there is a short in the wiring that leads to that area. If you can find your circuit box, look to see if any of the little switches appear to be in the off position. Unplug everything from those receptacles. Flip the switch to the on position. If it stays in that position, plug everything back in one thing at a time until something trips the circuit again. (If you are able to plug everything back in, it may have been a power surge that tripped the circuit. )If the switch will not stay in the on position even if nothing is plugged in, call an electrician. Those circuit breakers are there for safety.
Up to 12 on a 20 amp circuit. Up to 9 on a 15 amp circuit. But use common sense. If the circuit will be heavily loaded, as in a home office, then do not install that many.
Unless you do not have enough space in the service panel it is always a good idea to have each room on it's own circuit. If you want to put 2 rooms on a circuit just make sure those 2 rooms do not overload the circuit and wire it for a 20 amp circuit. Two bedrooms with 8 outlets each and 1 light each is about all you would want on the circuit. I would never put 3 rooms on the same circuit.
a schematic circuit is a diagram that show you how a particular circuit works
Yes. I know of no limits to how many regular receptacles (outlets) you can "piggy back" onto one GFCI receptacle. However, in commercial and industrial construction there are limits to how many receptacles can be placed on any one circuit. These limits in the United States and according to the NEC are: 10 receptacles on a 15 amp circuit and 13 receptacles on a 20 amp circuit.
In the United States and according to the NEC, in commercial and industrial installations, you are limited to 10 receptacles on a 15 amp circuit. The size of the wire is not a determining factor. There is no limit to the number of receptacles on a circuit in a home and there may be local codes where you live that have stricter requirements.
four
Many things can determin how many outlets are on one circuit. But for general lighting circuits the number is ten.
Rule of thumb is about 8 unless it is a dedicated circuit. The NEC has no requirements on the number of receptacles that can be on a circuit in a residential setting. The circuit should be layed out to only cover 500 sq. feet. A single room of 500 sq. feet, you could put as many receptacle as you want on one circuit.
The circuit probably tripped because too many things were plugged into the receptacles or there is a short in the wiring that leads to that area. If you can find your circuit box, look to see if any of the little switches appear to be in the off position. Unplug everything from those receptacles. Flip the switch to the on position. If it stays in that position, plug everything back in one thing at a time until something trips the circuit again. (If you are able to plug everything back in, it may have been a power surge that tripped the circuit. )If the switch will not stay in the on position even if nothing is plugged in, call an electrician. Those circuit breakers are there for safety.
If you are referring to the 25KW Power Distribution Panel used by the military, NSN: 6110-01-244-3209, there are four 120VAC, 20A circuit breakers and four corresponding twist lock receptacles.
This depends upon the circuit breaker capacity. You may never load a circuit to greater than 80% of it's capacity. So you may load up to 12 Amps on a 15 Amp circuit, and, 16 Amps on a 20 Amp circuit. The National Electrical Code requires you to calculate each receptacle at 180 VA. If the circuit is 120 volts and 15 amps, you would have 1800 VA, divide by 180 VA per receptacle, equals 10 receptacles per circuit (minus the wattage of each luminaire or light fixture added to the circuit, before dividing by the 180 VA). If the circuit is 120 volts and 20 amps, you would have 2400 VA, divide by 180 VA per receptacle, equals 13.333 receptacles per circuit (round down to 13 receptacles),(minus the wattage of each luminaire or light fixture added to the circuit, before dividing by the 180 VA).
Many different companies offer office space for sale. Some examples of these companies offering office space include Loopnet, Cityfeet, Showcase, and Regus.
Many companies and renting places have office space for sale or for rent you need google them to find ad.
Up to 12 on a 20 amp circuit. Up to 9 on a 15 amp circuit. But use common sense. If the circuit will be heavily loaded, as in a home office, then do not install that many.
There are many people to help an individual find an office space for rent. Many realtors specialize in this feature and can help find office spaces. Also, there are always signs on the outsides of buildings if a space is available to rent.