0
ten lights per curcuit
<<>>
Circuit loading
In Canada there shall be not more that 12 outlets on any 2 wire branch circuit. Such outlets shall be considered to be rated at not more that 1 amp per outlet. Where the connected load is known, the number of outlets may exceed 12 providing the load current does not exceed 80 % of the rating of the over current device protecting the circuit.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Feed drops to zero volts when light switch is turned on back to 120 volts when turned off feeds fluorescent lights?
voltage is measured by voltagd drops. When a switch is open/ off there is a voltage difference between one side to the other. when the switch is on there is no drop from one side of the switch to the other. That is normal operation. If switch is on, and you get a voltage reading across the switch, the switch is bad.
How do you get all of the light switches to be in the down position for off when you have more than one switch for them?
Three way switches do not have a up-on down-off position. With the lights off, reposition the switches so that the handles are all down. This is the start position and depending on how you enter the room and turn on the lights certain switches will be left up when you leave the room. That is just the design of the switches and for the asthetics of the look, all handles down the lights will be out.
What is the main purpose of SPDT and DPDT switches?
The number of poles refers to how may separate signals or if you will, wires you switch when the switch is activated or deactivated. For example your typical light switch just switches the hot wire and turns the light on or off and is called a SPST switch. The SPDT switches a signal to either of two circuits. So for example, if you had hot connected to the input and a light connected to each output (Throw), you would have one light on and one off and each time you throw the switch the lights switch which is off and which is on. The DPDT can switch two separate signals at the same time and each goes to one of two separate circuits. If you had two separate breakers and four light bulbs you could hook up one breaker hot to one pole and the other breaker to the second pole. If you had four light bulbs each connected to each of two switch outputs, then one bulb from each breaker would be on and when switched the other bulb on each breaker would be on. For diagrams just search for SPDT and DPDT.
What is electrical supply timer?
Hard to know what you are meaning? A timer is a device in a circuit that switches on then off at given times. There may be many on/off operations not just the one. Think of some lights, say street lights that come on at a certain time then off at a later time. If they are electric that would fit you question. Although the lights are more likely controlled by darkness at dusk and first light in a morning. G4CIR
Power is not off . need to change when you change the light switch?
Yes, you need to turn off the power when you change (replace) a light switch, since at least one of the terminals on the switch will always have power if the circuit is energized at the panel.
Four recessed lights one circuit switch off three lights on one off?
This question is difficult to understand. Please explain what you mean.
Why is there an external light switch on the house?
To turn off lights from the outside (I have one too).
The parking lights on your 2001 Subaru Forester do not go off The switch is not turning them off?
My 2000 model has a switch on top of the steering column for leaving the parking lights on when the engine is off. I don't know if the 2001 has one also, but if it does, try switching that.
Chevy Silverado lights do not work?
check your switch inside the cab (the one you actually use to turn lights on and off). Mine did the same thing and the switch had shorted out...should be an easy fix
How do you get the interior lights to turn off in 2006 Trailblazer?
Push the button. The one close to the headlight switch.
Why parking lights stays on after car is turned off?
Most likely because the switch is stuck in one position. Find the switch and repair or replace.
Why do at homes all the lights and fans go off if main switch is turned off?
A main switch is one which controls all the electrical power at a given house or other location. That's what is meant by main switch.
Your interior lights will not turn off How do you get them to turn off?
If the interior lights in a vehicle will not go off, first one should make sure all doors are closed. Then one should find the switch on the roof of the vehicle and make sure it is not turned to the on position.
Why would the head lights blink off and on while the switch is turned on in a 1965 ford mustang?
The switch is wearing out on the inside, just order a new one and replace it.
Why wont the running lights and interior lights go off?
you probably have a bad door light switch in your car, you need to check ever switch in the system its 5 ( 4 doors an a tail gate) I bet you one is defective.
What is wrong with a 2001 Legacy Outback when you turn off the car and the tail lights stay on?
Try checking the brake light switch. The brake lights are working fine. The running lights are staying on. The solution was the parking light switch on top of the steering column was in the "on" position. Switched it to off and problem solved. Actually never used the switch, guess one of the kids was playing with it... Thank you! That was a simple fix - i didn't even know that switch was there!
Feed drops to zero volts when light switch is turned on back to 120 volts when turned off feeds fluorescent lights?
voltage is measured by voltagd drops. When a switch is open/ off there is a voltage difference between one side to the other. when the switch is on there is no drop from one side of the switch to the other. That is normal operation. If switch is on, and you get a voltage reading across the switch, the switch is bad.
