0
How much area does a roll of rolled roofing cover not shingles?
Wiki User
∙ 10y ago
Roofing paper, or felt, normally comes in about 150ft rolls and are 3ft wide. Figure about 450 square feet of felt. Remember when estimating required amounts that you need to overlap the felt about 6 inches or so. With an overlap of 6 inches, 1 roll has a coverage of about 375 square feet.
Wiki User
∙ 14y ago
Wiki User
∙ 14y agoOne roll of mineral surface roll covers 100 square feet of roof deck. If you lay the product out flat and measure it, it's a little over 100 sf, but you overlap it when you apply it.
Add your answer:
Earn +20 pts
Where can I get roofing shingles?
You can get roofing shingles at any online home depot or home improvement store. You can also get shingles at lowes or any outdoor center available in your area.
What is foot span?
A foot span is a term used in the roofing industry to calculate the area of a roof. It is necessary to calculate how many shingles per foot. This measurement will vary depending on the type of shingles used.
Who reroofs roofs in my area for the cheapest price?
Its been widely reported and discussed on various roofing forums that roof shingles manufacturers are drastically raising the prices of their roofing shingles and accessories that go along. Some roofers report getting letters from their roofing suppliers that shingles prices are going up as much as 30%.
What is the lowest local price for roofing?
Let's say! Which roofing material is the least expensive? Asphalt shingles are the least expensive roofing material, costing between $100 and $150 per square foot.
How to repair different types of roofing?
Roofing repairs are needed when a roof system is leaking, or the roof has been damaged in some way, such as a fallen tree or high winds. The type of roofing will dictate the materials and the method of repairs, so it is first necessary to determine which type of roofing is in place. Once the type of roofing has been established the materials can be purchased. There are typical procedures that are used for repairing different types of roofing.Wood shingles will dry out and crack over time and when this happens, the roof will leak. The repair can be accomplished by replacing a section of the roof or by repairing the leaky sections using aluminum shingles. Aluminum shingles can be slid under the wood shingles and will act as another surface to ship water. The holes can be spotted from below, in an attic area, and the daylight that seeps through will signify where the aluminum shingles need to be inserted. If the leak is confined to an area of damage, remove the damaged shingles and re-roof that area. Be sure to lace the new shingles into the existing to ensure the roofing system is continuous.Composition shingles cannot be patched in any way that will make a suitable repair. To repair a composition shingle roof, remove the damaged singles in an area larger than the actual damaged area, in order to allow for lacing into the old roofing. Be sure to apply two layers of felt roofing paper to the roof sheathing before installing the new composition shingles. The new shingles can be attached using staples or galvanized roofing nails.Spanish tiles and concrete tile roofing will break when hit by hard objects. When this happens it is necessary to remove and replace the damaged tiles. Be sure to extend the area of repair outward from the damaged section in order to ensure a suitable repair. In addition, it will be necessary to replace the heavy moisture barrier under the tiles. The area of the new barrier should overlap the existing moisture paper to ensure a good under-lay system. Roofing tiles are held in place using a single, galvanized nail that is made for the particular tile. A qualified salesperson will be able to recommend the correct nails to use for a particular type of tile. Do not walk on the new roofing tiles once they are in place, as this could cause them to crack, which will result in further repairs.
How many rolls of 15lb roofing felt to cover 2000 sqft?
Five--a roll will cover 400 square feet of area.
How many square feet does 1 square of shingles cover?
One square of shingles covers an area equivalent to a 10 foot square, or 100 square feet.
What is meant by the term square and how much area does it cover?
A square usually refers to shingles or siding and it's the amount that covers 100 square feet (or a 10' x 10' area).3 bundles of shingles cover a square1 bundle of shingles covers a 4' x 8' sheet of plywoodSiding has a certain number of "square" per box
How many squares of shingles on area of 1732square feet?
A square of shingles covers 100 square feet. So, you need 1732/100=17.32 square of shingles. If you can only buy whole number squares of shingles, you will need 18 squares of shingles to cover 1732 square feet.
How many bundles of shingles would it take to cover a 12' x 15' shed roof?
How much area would 15 bundles of shingles cover. Standard duty shingles use 3 bundles for every 100 square feet so 15 bundles would cover 500 square feet.
How much area does a bundle of architectural shingles cover?
33 square feet
How manyPieces of roofing in square?
There are 21 shingles to a bundle and 3 bundles covers a 10 by 10 ft area. a basic rule is a bundle covers a sheet of plywood, then add some for valleys.
