Guessing you are replaceing an outlet? Black goes on the copper colored terminal and white on the same side that has the ground terminal. If you have checked and made sure that white is in fact the neutral you can run a jump wire from the side terminal to the ground. This will ground whatever you plug into the outlet as long as it has a 3 prong plug.
you can wire the single post toggle switch to the old school 2 wire system, just ignore the ground screw (like the old switch did).
no outlet
skip the outlet, just use the toggle switch
if you want an outlet you'll need to run a ground wire down to your electrical box
In North America (Canada, United States, Mexico) a household 110V-120V outlet has three wires: hot, neutral and earth ground. If the outlet is mounted in a grounded metal box, the third wire (earth ground) may not be present, since the connection to ground occurs through the metal outlet housing and possibly metallic conduit that routes the wires from the circuit breaker panel to the outlet. Where metallic conduit isn't used, the earth ground wire may be connected to the metal box, and the earth ground pin of the outlet is connected by securing to the box with screws.
Only leagl in a ring main in the UK.
The definition of an outlet in Article 100 of the National Electrical Code book (US) is: "Outlet. A point on the wiring system at which current is taken to supply utilization equipment." You can have a receptacle outlet, lighting outlet, or some other hardwired equipment outlet. <<>> The definition of an outlet in Section 0 (Object, Scope and Definitions) of the Canadian Electrical Code book is: "Outlet. A point in the wiring installation at which current is taken to supply utilization equipment."
No, the common American light switch is only rated for a maximum of 125 volts.
wiring diagram of one bulb in two switches.. example, if switch a- on then switch b- off the bulb is on, switch a- off then switch b- on the bulb is on, switch a- on then switch b- on the bulb is off, switch a- off then switch b- off the bulb is off..
No it is not hard to tell them apart. A Single Pole Single Throw switch will go directly from the on position to the off position breaking the circuit. This is the type of switch that is used in homes for lighting control. A Single Pole Double Throw switch will usually have a stop indent which is the off position mid way through the throw. This is the switch that is used for a transfer switch when using a stand by generator in the system. The full up (on) position is usually connected to utility power. The full down (on) position is usually connected to the stand by generator.
This looks like a question that has come out of the middle of a conversation. Us poor guys trying to answer the question don't have any context. We don't know what the intermediate switch is; or anything else about the system. You can always use just one side of a two pole switch to replace a single pole switch.
Outlet: A point on the wiring system at which current is taken to supply utilization equipment.
The alarm switch system is not working right. This could be a door switch, or a wiring problem. the system needs to be checked one switch at a time, then the wiring is checked next.
The definition of an outlet in Article 100 of the National Electrical Code book (US) is: "Outlet. A point on the wiring system at which current is taken to supply utilization equipment." You can have a receptacle outlet, lighting outlet, or some other hardwired equipment outlet. <<>> The definition of an outlet in Section 0 (Object, Scope and Definitions) of the Canadian Electrical Code book is: "Outlet. A point in the wiring installation at which current is taken to supply utilization equipment."
The definition of an outlet in Article 100 of the National Electrical Code book (US) is: "Outlet. A point on the wiring system at which current is taken to supply utilization equipment." You can have a receptacle outlet, lighting outlet, or some other hardwired equipment outlet. <<>> The definition of an outlet in Section 0 (Object, Scope and Definitions) of the Canadian Electrical Code book is: "Outlet. A point in the wiring installation at which current is taken to supply utilization equipment."
You can get wiring diagrams from MOTORLIT.COM or shop ,manuals from AUTOBOOKSONLINE.COM
No, the common American light switch is only rated for a maximum of 125 volts.
The steps to switch on a computer begin with making sure that the computer and its peripherals are plugged into an electrical outlet. Turn the power switch on the electrical outlet and press the power button on the computer tower. Turn on the computer monitor and wait for the computer system to start up.
Three phase wiring is rarely used in homes in the United States. It becomes a fairly complicated process when most homes have a single phase wiring system.
The ignition wiring can vary with different years of Warriors. The system should have two wires for run and two wires for kill. a wiring diagram for your particular year will show the color codes for the exact wiring.
I have the 28E6 with a dimmer switch and need to replace them. How can I locate this product for replacement?
A Intel system bus is a single computer bus that connects the components of a major computer system. The system bus also referred to as crossbar switch.
wiring diagram of one bulb in two switches.. example, if switch a- on then switch b- off the bulb is on, switch a- off then switch b- on the bulb is on, switch a- on then switch b- on the bulb is off, switch a- off then switch b- off the bulb is off..