0
That dimension will change with the size of the window and the header height.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is Length of window cripple stud?
The length of a window cripple stud typically ranges from 12 to 24 inches. However, the exact length may vary depending on the specific design and size of the window, as well as the construction standards in a particular region.
How much is a 2 by 4 by 8 stud?
64 cubic units of measurement.
How do you replace broken stud on 95 f 150 4x4?
Are you asking about a wheel stud or exhaust stud, please clarify
How do you know how many studs in a wall length?
The studs should be 16" apart.If you're estimating the lumber, figure 1 stud per linear foot of wall.You'll need the extra's for corners and headers and plates.
What does on center mean?
It means from the centre of one object to the centre of another. For instance, wall studs are usually 16 inches on centre. So, from the centre of one stud to the centre of the next stud it is 16 inches.
What is Length of window cripple stud?
The length of a window cripple stud typically ranges from 12 to 24 inches. However, the exact length may vary depending on the specific design and size of the window, as well as the construction standards in a particular region.
How do you calculate the length of a stud?
with a measuring tape
What are the types of jack?
There's blackjack, a roofing adhesive. Also--ladder jack, jack stud, jack hammer, hydraulic jack, jack rafter, jack post, Jack Bower, etc.
What is a Jack stud?
A post in which it holds the jacks against / within the wall framing
How do you remove the manual window crank on a 1999 Pontiac Sunfire?
How do you remove the manual window cranThere should be an Allen type set-screw in the base of the handle. It will be recessed, and you'll have to turn the crank to access it more easily. Remove the setscrew, and the handle slips off of the stud. If the window is down, and it begins to rain, you can roll the window up by holding it onto the stud, and turning, or you can use a small pair of vise grips. Just try not to damage the teeth on the stud.
How do you replace a broken wheel stud in front wheel?
Jack the car up and remove the front wheel. Use a jack stand for safety. Rotate the axle until the stud is over the hole in the backer plate. Hit the stud with a hammer, this will take many blows. The stud will pop out. Slide the new stud in, then stack several washers on the shaft and put a lug nut on. Tighten the nut to pull the stud up tight into place. Reinstall the wheel, and over the next few days, keep checking the tightness of the stud to keep it snugged up.
How much is a Roblox stud?
Oh, I found an answer on a forum: 1 stud = 1 foot
What length labret stud would you need to use as an earring?
8mm or 5/16"
What is the length of a pre-cut stud for a 8' wall height?
92-5/8"
What is difference between Stud and stud bolt?
stud has all its length threaded and it is used with two nuts, but the bolt has one end closed and the other end is threaded ,it is used with a single nut.
How much is a purple LEGO stud worth?
In the Lego video games, a purple stud is worth 10,000.
How do you replace front wheel stud bolt on 1996 suburban?
Jack up the vehicle and put a safety stand under it. Take the wheel off. With a hammer hit the stud on the tip, several blows should knock it loose. The stud can be pulled out from the rear. Slide a new stud into place, and put to two or three washers on it. thread the nut on, then tighten it. The nut will pull the stud in tight. Remove the nut and washers, then remount the wheel.
