answersLogoWhite

0


Best Answer

For an accurate calculation it will be necessary to know what the size of breaker exists in the pump house and what size conductors are used. Power loss is measured using actual amps required, not size of the circuit involved. But the size of circuit (breaker size) can be used. Voltage must also be known.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How much loss from power pole to 200 amp breaker box then off 400 feet then split at a pump house then another 30 feet to a 100 amp breaker box?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Natural Sciences

Can I add a circuit breaker wired in parrell to a current breaker to reduce the load on the breaker?

No, add new breaker,find a junction box and split the series, or add a box and split the load. You only need to do this if the breaker is tripping from overload. 12ga wire should have a 20amp breaker not a 15amp. If I understand your question,wired in parallel, this would be one hot connected to two breakers, first off two breakers is 220v not 120v , and 220v has two hot wires. Never connect two breakers together on one line.


Can you use two 15 amp single pole breakers in place of a double pole 30 amp breaker?

Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.


Can you install a tandem breaker?

Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.


How do you tap into a 220v feed going to baseboard heater and get a 110v supply?

This is only valid in parts of the work using 110/220 Volt split phase power system. There will be 110V from each of the hot leads to ground/neutral, so connect your outlet to only one of the hot leads, the neutral lead and the earth ground lead. This may be a problem with a dedicated 220V circuit as there will likely be no neutral line. Another note - this could well cause an unbalanced electrical load across the two pole breaker. If the breaker has a rating of 20A and the 110V circuit draws much of that current, the heater will likely trip the breaker.


What is a tripped circuit breaker?

As far as a fuse like in a car or even larger versions of the fuses in a car you should be able to see inside the little wire; if the fuse has burnt amd is split in two parts the fuse has been broken. In a circuit breaker it works a little differently, instead of burning out and needing to be replaced, the breaker will "trip" this means there is too much current being drawn through the circuit and the setup cannot handle it. A breaker instead will click to the off position and the switch will flip from on to off. These are much easier to locate than a burnt fuse because in a breaker box usually all the switches are turned to on and in the same direction, so the one breaker that did trip will be pointed in the opposite direction. Simply flip the switch from off to on and its been reset. If the breaker keeps tripping then there is either a short or you have too many loads (appliances) running on that circuit, for instance a power strip with 6 things plugged into it all running at the same time.

Related questions

Why did Jeff foxworthy and his wife split apart?

Infidelity, the age old breaker upper :(


Can the president of Ireland veto a constitution?

yes but he can be by passed by the house ans senate the president really has no power when you work the system the power is split between the branchs of goverment.


Can I add a circuit breaker wired in parrell to a current breaker to reduce the load on the breaker?

No, add new breaker,find a junction box and split the series, or add a box and split the load. You only need to do this if the breaker is tripping from overload. 12ga wire should have a 20amp breaker not a 15amp. If I understand your question,wired in parallel, this would be one hot connected to two breakers, first off two breakers is 220v not 120v , and 220v has two hot wires. Never connect two breakers together on one line.


Can you use two 15 amp single pole breakers in place of a double pole 30 amp breaker?

Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.


How does the electric distribution panel work?

It's basically a system of circuits. The power from the mains enters through the input terminals. It's then split into various load circuits (5 amp for lighting, 13 amp for sockets , 15 amp for the immersion heater & 30 amp for cookers). Each of these circuits has it's own circuit breaker, which cuts the power to that particular circuit if the current draw exceeds the rating of the breaker.


Can you install a tandem breaker?

Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.


Why was the two house system created?

The two house system or duplex was created to make more living space in older homes. Sometimes the house in question was renovated and split down the middle to make another separate apartment.


When parliament split into 2 parts what was the lower house?

the house of commons


What is another name for split?

saliva


Where can i get information on a split level cooker?

the split level cooker is very easy to clean and is built into the house


How do you tap into a 220v feed going to baseboard heater and get a 110v supply?

This is only valid in parts of the work using 110/220 Volt split phase power system. There will be 110V from each of the hot leads to ground/neutral, so connect your outlet to only one of the hot leads, the neutral lead and the earth ground lead. This may be a problem with a dedicated 220V circuit as there will likely be no neutral line. Another note - this could well cause an unbalanced electrical load across the two pole breaker. If the breaker has a rating of 20A and the 110V circuit draws much of that current, the heater will likely trip the breaker.


Can you lose your house if your girlfriend and you split up and the house is in one name?

If it's in her name.