You could, but if you're going to do that then why not ground the entire service entrance panel? ...and you need to drive (if I remember correctly)...about 7 feet into the ground to be effective.
No the re-bar will rust in the ground when exposed to the ground dampness. This will cause the rod ground resistance to gradually increase. Approved ground rods are either copper clad or galvanized. In locations where it is impossible to drive a 10 foot rod into the ground the electrical code has approved ground plates that can be dug in and buried at two feet in depth. You want the resistance to be as low as possible on a grounding circuit. Alternatively, if that re-bar is part of the concrete foundation (Ufer ground) of the structure (and at least 20 feet long, 1/2" min. diameter) it is a perfectly acceptable grounding electrode. [NEC 250.52A3]
Is it all wheel drive? no then lift the front and tow away.Do not drag it down the road with the drive tires on the ground unless you want to put a transmission in it.
A four blade dryer plug cord should have a red, black, white, and green wire in the cord set. The red and black wires are the ones that deliver the 240 volts to the dryer. Black and white deliver control 120 volts to the dryer and also drive the motor to turn the dryer drum. On some dryers they use the red and white for the motor and black and white for the control. As for the green it is always the ground wire.
Grounding a pool is serious business, there are many risks if this is not done right. Grounding also varies depending city, county, state, country. For starters, you can't have a good enough ground for your pool. This is one case where more is better. As a general rule, you could drive a 10 ft copper ground rod at each corner of the pool. Then you could drive more 10 ft copper rods at each end and the middle. On each metal pool stanchion you have to put a suitable sized grounding lug that's threaded into the metal. You then start a #6 bare copper wire from the first rod and clamp and run it continuously through each stanchion. You then tie the end back into the first rod creating a ground loop/grid. Again, this varies from place to place. Here is my suggestion. Call your local electrical inspection department, and see what they want done. Before it's closed in, weather decked or concrete it has to be inspected for your safety. When in doubt, always consult a licensed electrician from your area for local rules.
do not get a boat out because the boat is probably going to get smashed
You need a XSATA Hookup/cable or an Xplorer 360 Hookup/cable.
copperclad is steel with copper over it steel will drive into the ground and push small rocks out of its path copper doesnt rust but is soft copper will last far longer copper clad takes the good parts of both you can bury a copper plate for lower impedance
Unless otherwise specified you need a 5/8th inch by 8 foot copper clad rod. A great trick is to drive it in at a 45 degree angle and bend it up as you go so it ends up straight after it drive in all the way. This keeps you from hitting hard pan and keeps you from having to get on a ladder to drive the rid which can be kinda dangerous. Leave about 4 inches out of the ground for you ground clamp. For a 200 amp service use #4 armored ground. For 125 amp or 100 amp you can use #6 armored ground wire and an armored ground clamp. The NEC allows that for ANY connection to ground rod, #6 solid copper is the largest conductor required. The ground rod is SUPPLEMENTAL, and only in rare circumstances is the ground rod your primary ground. The sizes given above are for your primary grounding connection, such as a metal water line.
mini copper
You need to plug the ethernet cable into a port located on the back of the console, near the hard drive.
Both - you fly it in the air, but you drive it on the ground.
Roads are the black hard stuff on the ground for cars to drive on. Roads are made of tar. Tar is sticky black stuff that is made of tree skeletons.
I need a diagram for a ground drive belt for John Deere S2546 lawn tractor.
The 2013 Chevrolet Black-Diamond-Avalanche has rear wheel drive.
A post Pounder can in fact drive posts through solid ground. It would work great for putting a fence into your property even if the ground is frozen solid.
Copper Creek golf club is located at 4825 Copper Creek Drive, Pleasant Hill, IA 50327. Copper Creek golf club was built in 1997 and has a 18-hole golf course.
Burn Drive, Shock Drive, and Douse Drive.