0
Several variations of Ethernet exist. At some moment, a bus topology was quite common, but nowadays, a star or extended star - with a hub or switch at the center of the star - is more common.
Several variations of Ethernet exist. At some moment, a bus topology was quite common, but nowadays, a star or extended star - with a hub or switch at the center of the star - is more common.
Several variations of Ethernet exist. At some moment, a bus topology was quite common, but nowadays, a star or extended star - with a hub or switch at the center of the star - is more common.
Several variations of Ethernet exist. At some moment, a bus topology was quite common, but nowadays, a star or extended star - with a hub or switch at the center of the star - is more common.
Wiki User
∙ 14y ago
Wiki User
∙ 14y agoSeveral variations of Ethernet exist. At some moment, a bus topology was quite common, but nowadays, a star or extended star - with a hub or switch at the center of the star - is more common.
Add your answer:
Earn +20 pts
What is the function of bus topology?
The bus topology is one of the four main topology types for networking. It allows systems to be connected in a straight line without any other network connectivity devices. As a result, it is easy to construct and needs very little in the way of configuration, and is inexpensive compared to other topologies. The main result of any topology is to connect clients together in order to share resources.
Which two pieces of information are documented in a logical topology map?
#IP addressing#group usage information
What are the advantages of fully connected topology?
Advantages:A fault in one terminal on the network will not effect the rest, as the data has multiple reduntancy paths, depending on the size of the network, that are open to it.When network usage is high, data packets can be transmitted via different cables, thereby reducing network clogging - keeping data transfer rates at an acceptable level.Disadvantages:A large amount of cabling is required.
Discuss the difficulties that one encounters when trying to build a bridge between the various Ethernet Token Ring and Token Bus LANs.?
Since there is no protocol known as Ethernet Token Ring I assume you are asking about the difference between Ethernet, Token Ring, and Token Bus usage. These are all different protocols, so connecting all three types of networks is not practical. Token Bus networks were an early attempt to get mainframes to connect to terminals through a bus topology structure, utilizing a token for arbitration. Those networks typically ran at 4 Mbps. They were also subject to the same problem as a linear bus structure with Ethernet, which is a break in the cable would bring down the entire network. A later version of Token ring uses a ring topology structure, where a failure in the network will not bring down the entire network. It still uses a token for station arbitration, but can ran at 16 Mbps. Newer versions of HSTR can run at 100 Mbps and there is a standard for a gigabit version. Chances are you will need to bridge between Ethernet and Token Ring (not token bus). For that, you will need a bridge, router, or gateway that can convert between the protocols. In some cases the media is different as well, going from coaxial cable to unshielded twisted pair (UTP). So the difficulties are in correctly converting the protocols between the two, connecting different media types together, and troubleshooting problems between the two networks.
Which is the best network hub for home usage without paying too much money?
The Startech.com Network Hub
What is netflow?
Netflow is a Cisco product to analyze network bandwidth usage.
When referring to computer networking what is a network service?
The network service is a medium of data manipulation and usage. Concerning computer networking, a network service is fundamental to the functioning of a computer network.
How can you block your employer from viewing your web usage?
If you are using your employer's computer or network access, you cannot block them from seeing your web usage.
Is client server network system economical for usage of 5 systems?
yes
What is an anomaly based system?
Anomaly-Based systems define normal activities in term of network traffic and system resource usage so that any deviation from the defined baseline is consider an attack. anomaly-based systems are typically rolled out with the learning period in which all relevant parameters are analyzed.
What factors do you need to consider when implementing VoIP within an existing network?
You have to consider the size of phone network, call duration, usage and speed of the internet which will host as a communication network.
Which are good criteria to break a large network into multiple access layer network?
Logical Grouping, Physical Location, Application Usage, Security...ALL
