0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When a multiple is shared by two or more numbers that multiple is called?
A common multiple. If it is the lowest possible combination of those numbers, it is called the Least Common Multiple or LCM.
What is a possible missing digit in 23 87 if it is a multiple of 5?
55
What is greatest possible number that is less than 70 and is a multiple of 6 is?
66
The possibility of multiple hazards occurring simultaneously is possible true or false?
True
What is the least multiple of 6?
There is no possible answer since if x is a multiple of 6 then x-6 is also a multiple of 6 and it is smaller. This process can be applied over and over - all the way to negative infinity! The least non-negative multiple is 0, the least positive multiple is 6.
What does i2c stand for in the terms of power?
In terms of power I2C stands for an "Inter-Integrated Circuit". An I2C is used to connect slow speed computer components to the motherboard or other electronic devices.
What is the difference between i2c and spi?
Major Difference Between SPI and I2C is: SPI is full Duplex (SPI can be full/half duplex, depending on the hardware, 3 or 4 wire) and I2C is half duplex communication....we cannt send and receive data at a time in I2c..but it possible in SPI ....SPI much faster Than I2C....... Main topic to discuss the difference is 1) speed is difference in case of i2c is 100/400kbps in 7 bit mode max 400kbps (But High speed I2C communication protocols allow speeds upto 3.4Mbps!!) in case of spi speed is upto 1mbps (the higher speed of SPI is due to fact that unlike I2C, SPI interfaces to a slave device using a sperate pin called the slave select + no concept of acknowledgements which means increased Band width..) 2)Connection wise: i2c require less pin then spi (SPI 3wire: 3 IOs, SPI 4 wire: 4 IOs, I2C: 2 IOs) as spi require slave select for individual device... 3)it is better to use i2c in case of if u want to connect more device to connect. (slave addressing advantageous over SPI slave select individual pins for individual slaves) 4)bus arbitration is possible in case of i2c... not in case of spi... (SPI does not require it, since only 1 slave is controlled by the master at any given point) 6)noise sensitivity of i2c is high... there is chance to corrupt the r/w bit... then whole data is corrputed... but in case of spi.. chance is very less as whole word is trasmitted... However, I must say that I2C is more reliable, since the protocol supports slave feedback machanism (ACK) to detect whether was received correctly or corrupt. 8) it is easy to implement the spi...while i2c is little bit complex... (over heads) Formatted Answer @: http://www.bubblews.com/account/65122-kapilddit
What is the difference between i2c and rs232?
I2C (Inter-Integrated Circuit) is a serial communication protocol that uses two wire lines for communication, allowing multiple devices to be connected in a network. RS232 (Recommended Standard 232) is a serial communication standard that uses a single wire for data transfer and is commonly used for connecting devices like modems, printers, and GPS receivers. Additionally, RS232 uses voltage levels for signaling while I2C uses open-drain signals.
What is the What is the difference between master's and masters?
masters is multiple masters and master's is possession:"that's the master's magic wand."
What is the differences between i2c and can bus?
hfghfgh
Is it possible to do several masters at one time?
Yes it is possible to go for several masters degrees at one time. It is extremely difficult.
Which universities in Canada offer masters degrees in communications?
No universities in canada offer masters degrees in communications. But, in Canada there are multiple schools.
Will there be a season 4 of ninjago masters of spinjtizu?
possible
What is the difference between CAN and I2C?
We can use I2C only for small distance communication not more than 1 meter, but CAN bus can be used for more than this distance that's why in todays world CAN bus is most preferred in Automotive Industry.
What are the 2 roles of nodes in I2C communication?
Two roles of nodes in I2C communication are: master and slave.Master node - node that generates the clock and initiates communication with slavesSlave node - node that receives the clock and responds when addressed by the master
Is it possible to link multiple Game Cubes?
It is not possible to link multiple Game Cubes
Which multiple Masters champion tied a record for the lowest final nine and the highest final nine by a winner?
Gary Player is the multiple Masters champion who tied a record for the lowest final nine and the highest final nine by a winner. The name of the very first Masters was the August National Invitation Tournament.
