0
the number of bits required to represent an instruction of a cpu is known as length of the instruction or known as instruction.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What are the advantages of using a variable length instruction format?
One of its advantage is to save storage space.
What is Convert 3 inches to mm?
It is an instruction to convert a measurement of length from a near obsolete system to one that most people in the world use.The conversion factor is 1 inch = 25.4 millimetres.
What is the length of image if the scale factor is 8 and the length of figure is 10yds?
Length of image = Length of original*Scale factor = 10*8 = 80 yards.
Is the length of a side of a square and its area nonlinear?
I assume you mean the relationship between the length and the area. Indeed, it is non-linear. The increase in area is proportional to the square of the length of the side. For example, if the length of the side is increased by a factor of 10, the area is NOT increased by a factor of 10, but by a factor of 100.
How do you get rectangles from a list of factor pairs?
The factor pairs are the length and width of the rectangles.
Definition of instruction length it has something to do with computer?
what is instruction length and what is instruction format and what is program length and what is the difference among them
What are the advantages of using a variable length instruction format?
One of its advantage is to save storage space.
How much time does it take to film a full length movie?
Anywhere from a few weeks to a few years. Usually the deciding factor is money.
What is the meaning of FLM?
FLM-Focal Length multiplyer, the ratio of the image sensor format size of a camera compared to a reference format, which is also called crop factor.
What the advantages and disadvantages of using variable length instructions?
. fixed-length instructions · advantage: fixed-length instruction is fast and results in better performancewhen instruction levelpipelining is used. · Diadvantage: wastes space b. variable-length instructions · Advantage: Variable-length instruction saves storage space/ · Disadvantage: more complex to decode
What is the length of the instruction queue in 8086?
6 bytes
What is instruction format in computer architecture?
The connection between the hardware and software components of a computer creates the computer architecture. It is basically how the components are connected to form a complete system. Sir Frederick P. Brooks and Sir Lyle R. Johnson presented the idea of computer architecture in 1959. A set of operating codes, operands, an opcode, and an addressing mode make an instruction. The instruction format is the standard instruction format that is directly used by the CPU. The instruction format is just the sequence of bits (0,1). The group of these bits is called a field. Each field of the system provides specific information for a particular task to the CPU about the instruction's operation and the instruction's data. The most fundamental difficulty in format design is instruction length. The longer the command will, take longer the time to fetch it. The types of Fields are discussed below: Operation Field: It specifies the operations that are performed by the instructions like, ADD, SUB, etc. It can be any value or number on which the task has been performed. Operation field is mandatory for every instructor Address Field: It specifies the address of the operand. It refers to the address where the operand is stored. On the basis of multiple address fields, the instruction is categorised as follows: Zero address instruction: The operand positions are implicitly represented in zero address instructions. The stack-organized computer system supports these commands. One address instruction: This instruction manipulates data with the help of an implicit accumulator. Accumulator is a register that performs a logical process for the CPU. It uses one address field. Two address instructions: This address instruction is mostly used. This address command format has three operand fields. In the two address sections, registers or memory addresses can be used. Three address instructions: A three-address command must contain three operand components in its format. These three fields could be registers or memory locations. The instruction pipeline in computer architecture The instruction pipeline in computer architecture shows the system's instruction flow. It has 4 major segments, which are discussed below. Segment 1: The instruction fetch part can be performed using first in, first out (FIFO) buffers. Segment 2: The second section decodes the memory-fetched command before the effective location is computed in a different arithmetic circuit. Segment 3: The input is fetched from memory. Segment 4: The execution of the instructions is performed. Some of the features of instruction are : Addressing model: This is the first part of the instruction format. Data over the instruction format can be represented as an addressing format, and data is stored in the computer's memory or in the CPU's register OPCODE(operation code): This is the second part of the instruction format, and the opcode instructs the processor to perform the desired operation. Operand: Depending upon the processor instruction format, it contains zero to three operands, and this part specifies the data or points to the address of the data.
What is Convert 3 inches to mm?
It is an instruction to convert a measurement of length from a near obsolete system to one that most people in the world use.The conversion factor is 1 inch = 25.4 millimetres.
Why the length of instruction queue is 6 bytes?
increases speed
What are the important instruction set design issues?
# Operation repertoire: How many and which operations to provide, and how complex operations should be # Data types: The various types of data upon which operations are performed # Instruction format: Instruction length (in bits), number of addresses, size of various fields, and so on. # Registers: Number of CPU registers that can be referenced by instructions, and their use. # Addressing: The mode or modes by which the address of an operand is specified
What is the length of image if the scale factor is 8 and the length of figure is 10yds?
Length of image = Length of original*Scale factor = 10*8 = 80 yards.
What are the relationship between the area scale factor and the side length scale factor of similar figures?
The area scale factor is the square of the side length scale factor.
