0
It is the conductor that is used in service distribution panels that bonds the distribution panel's neutral bus bar to the ground electrode (rod). This brings all of the distribution panel neutrals that are connected to the same supply system to the same potential, that being zero. Should a supply service neutral open this ground wire will maintain the systems integrity until repairs can be made.
Wiki User
∙ 12y ago
Anonymous
conductor used to. connect the system grounded conductor
Add your answer:
Earn +20 pts
Does the Nec allow grounding electrode conductor to be run in conduit that has other conductors in the conduit and what code section?
No, the bare copper grounding conductor can not be in a conduit with other conductors. It can be in conduit by itself to provide mechanical protection for the wire.
What is the smallest size of a common grounding electrode conductor installed for multiple separately derived systems?
3/0 awg wire
What size is the grounding electrode of a 400 amp service 500CM?
In Canada the grounding electrode requirement is for two steel 5/8" x 10' copper clad rods spaced 10 feet apart.
What size copper grounding electrode conductor is required for a service that has three sets of 600 kc mil copper conductors per phase?
The grounding conductor of a service distribution is sized by the ampacity of the service. By just stating the wire size, this does not give this information, as many variables enter into what wires are used depending on length, ambient temperature and insulation factor to name a few.
Why electric arc furnace shell to be grounded?
Which is the mínimum distance between the electrode an a grounding part.
If you have a 400 Amp service using 500 MCM What size grounding electrode conductor is required?
#2
Does the Nec allow grounding electrode conductor to be run in conduit that has other conductors in the conduit and what code section?
No, the bare copper grounding conductor can not be in a conduit with other conductors. It can be in conduit by itself to provide mechanical protection for the wire.
What is a conductor used to connect equipment or the grounded circuit of a wiring system to a grounding electrode or electrodes?
The conductor used to connect equipment or circuit to an earth electrode is earth bond or in some cases a supplementary bond. This will be generally carried out using a copper tape or an earth cable.
What is the smallest size of a common grounding electrode conductor installed for multiple separately derived systems?
3/0 awg wire
Is the metal frame of a house an approved grounding electrode?
No, but the frame of a metal house must be grounded to an approved grounding electrode.
What electrode is used for grounding for an ECG?
V1
Iec 60502 2xfgy 61kv xlpe can you use the armour as grounding conductor?
NO some armored cable has a ground some sealtite has copper in the helix wit the drain shield some liquite has no conduction at all all armor is a helix which is a coil and acts as insulation at hi frequency xlpe cross linked polyethylene is an insulator service cable is never used for grounding grounding electrode conductor grounding equipment conductor grounding conductor are all separate from service cables if a tall trucks hits an overhead cable you dont want to lose the ground in short NO
What color wire is grounding conductor?
The grounding conductor is green, green with a yellow tracer or bare copper.
What is the difference between pipe earthing and plate earthing?
Assuming your reference to "earthing" is grounding (Grounding Electrode Conductor), a pipe is, as it sounds, a pipe (i.e. water pipe). A plate would be, as it sounds, a square (or rectangular) copper plate which would be buried in the ground.
What is the process of bringing a negatively charged conductor in contact with the earth resulting in the conductor discharge until it is completely neutral called?
short
What size is the grounding electrode of a 400 amp service 500CM?
In Canada the grounding electrode requirement is for two steel 5/8" x 10' copper clad rods spaced 10 feet apart.
What size copper grounding electrode conductor is required for a service that has three sets of 600 kc mil copper conductors per phase?
The grounding conductor of a service distribution is sized by the ampacity of the service. By just stating the wire size, this does not give this information, as many variables enter into what wires are used depending on length, ambient temperature and insulation factor to name a few.
