0
"Locked Rotor Current" also called LRA which stands for Locked Rotor Amps, is commonly found on electric motor nameplates. Locked Rotor essentially means the motor is not turning. The current or amps in this case have to do with the amount of electrical energy required to start the motor. At the instant the motor is switched on, it is not turning, and draws the maximum current. As the motor starts to turn, the current goes down. This required energy is much greater than the Full Load Amps or Running Amps, which is the current drawn when the motor is running at normal speed under full load. The current required to start the motor will depend on the type of motor as well as the specified design voltage required for the motor, typically the higher the voltage, the lower the required amperage or current.
The term also applies to equipment such as Air Conditioners which have an enclosed motor inside the compressor, as well as the condenser fan(s) etc.
Depending on the type of motor, LR current can be anywhere from 3 to 8 times the normal running current, also called RLA, or running load amps.
Wiki User
∙ 11y ago
Wiki User
∙ 14y agoThe maximum torque a specific motor can produce and the maximum current measured in amperes a motor should draw under full load.
Wiki User
∙ 9y agoIn order to calculate locked rotor current, you must consult the data plate from the specific manufacturer. There is no specific formula for this value.
Add your answer:
Earn +20 pts
What is locked rotor?
Locked rotor current is the amount of current a motor would draw if you energize the motor and the rotor (the spinning shaft) doesn't spin.
What is the locked rotor current on a 3 ton air conditioner?
You need to first know the wattage of the motor and locked rotor current can be tested at a lab only
What is difference of blocked rotor and locked rotor protection of motor?
What is difference of blocked rotor and locked rotor protection of motor?Read more:What_is_difference_of_blocked_rotor_and_locked_rotor_protection_of_motor
What are No Load And Locked Rotor tests on a three phase induction motor?
Doing a No Load test of a 3-phase induction motor involves the measuring of current, voltage, torque etc with no load on the rotor shaft, meaning that it is free to turn but is not driving anything else. Similarly a Locked Rotor test involves the measuring of current, voltage, torque etc with the rotor shaft "locked" i.e. prevented from turning, which is the worst loading condition the motor would ever have to contend with.
What is LRA of a motor?
Locked rotor ampere
What is locked rotor?
Locked rotor current is the amount of current a motor would draw if you energize the motor and the rotor (the spinning shaft) doesn't spin.
Is the induction motors running current or its locked rotor current more important in generator selection?
Running current. The locked rotor amps are only seen at initial start up which only lasts a fraction of a second to one or two seconds.
What is the locked rotor current on a 3 ton air conditioner?
You need to first know the wattage of the motor and locked rotor current can be tested at a lab only
What is locked rotor in three phase induction motor?
A motors locked rotor current is the same as the motors starting current. This is the point where the voltage is applied to a non rotating motor, time cycle zero. Because the motor is not rotation and generating a back EMF to oppose the inrush current, the current will go as high as 6 times the running current of the motor.
Different between locked rotor current and starting current?
difference between them based on the time where time of starting current equal to 2:8sec. & time of locked rotor current equal to 20:25 sec. so it is called also long start time fault.
What current would be drawn by a 15KW 400V AC motor with a locked rotor?
yes
What is difference of blocked rotor and locked rotor protection of motor?
What is difference of blocked rotor and locked rotor protection of motor?Read more:What_is_difference_of_blocked_rotor_and_locked_rotor_protection_of_motor
What is locked rotor current for 3 ton AC?
LRC for 3 ton AC is approximately 5 double the running current (75 A )
What are No Load And Locked Rotor tests on a three phase induction motor?
Doing a No Load test of a 3-phase induction motor involves the measuring of current, voltage, torque etc with no load on the rotor shaft, meaning that it is free to turn but is not driving anything else. Similarly a Locked Rotor test involves the measuring of current, voltage, torque etc with the rotor shaft "locked" i.e. prevented from turning, which is the worst loading condition the motor would ever have to contend with.
Why locked rotor test is performed?
Electrical machines such as motors are designed to withstand a certain maximum rated current (continuous) and a fault condition current for a short duration only. In order to practically verify this capability, a locked rotor test is performed on the motor as part of the final factory acceptance test. The motor rotor is mechanically locked and rated current is applied to the stator winding incrementally, starting from zero, all at rated supply voltage and frequency. Motor stator winding temperature is monitored and also the shaft output torque can also be calculated, if a load cell or strain gauge is connected to the torque arm. Therefore this locked rotor test (which is equivalent of a short circuit test for a generator) is used to verify the maximum current handling capability of the motor. Anush GE
Locked rotor current Where and how is it used sizing and specifying equipment for motor installation?
The specifics of this are found in Article 430 of the National Electrical Code.
What is LRA of a motor?
Locked rotor ampere
