0
copper
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
If I'm building a 5 inch rise per 12 inch run roof what are all the degrees for each angle cut to build 12' long common trusses?
the 2 common angels needed to cut a 5/12 pitch are 22.6 degrees and the reciprical 67.3
What is the adjective of rise?
low-rise adjective (BUILDING)low-rise adjective (TROUSERS)
What is the formula for figuring how to build steps?
Three parts of a step: Rise, Run and Width Width determined by use. Step 1 - Determine number of steps Best Rise for steps is 6-8 1/4 inches. Divide total rise (height of climb) by 7. This is comfortable average step height. Round off number to integer (can't have fractional steps) Step 2 - Determine actual Rise Divide total rise by number of steps from Step 1. This is your actual rise. Step 3 - Determine Run Two Formulas 1) Rise plus the Run should equal ap­proximately 17.5 inches. 2) Two times the Rise plus the Run should equal between 24 and 25 inches With 7 inch rise: Formula 1 - 17.5 minus 7 gives Run of 10.5 inches Formula 2 - 24.5 minus 14 gives Run of 10.5 inches ********************** Answer Measure how high the step need to be, say 4 ft. high. decide how high you want each step to be. Say 6 inches to make it easy. Devide the number of inches in each step into the total height. to raise 4 ft. you would need 8 steps. 6 inches into 48 inches goes 8 times. Height of step can be anything, an odd amount, 6 and 3/4, 7 and 1/4 whatever it takes to make them come out even. Use a framing square to lay out the stair on a 2x12 long enough. Again, using a 6 inch rise and a 10 inch wide step for example. On the top edge of the 2x12 take the framing , hold it in front of you with you being on the inside of the angle. The 2x12 is in front of you. The edge of the board closest to you is the top. On the outside edge of the square, put the right hand side at 10 inches and the left hand side at 6 inches and mark the outside of the square. Move the square up the board and put the 10 inch mark at the top of the 6 inch mark you just made and mark it again. Continue this till enough steps are marked. Square the top and bottom to fit the ground and the porch you are attaching to. I hope this is clear enough, it's easier to show than it is to explain.
What is the rise of a line?
Rise of a line is a positive slope.
Slope is rise divided by run?
Yes, rise divided by run
What are the standard measurements for commercial steps?
7 inch rise and 11 inch run
What is 3 feet for every one inch?
If you're talking about a slope: 3 foot run over a 1 inch rise.
A rise as little as can cause a person to trip and fall?
3/8 inch
What is the percent of rise if 1 inch per 3 feet?
12 inch = one foot 36 inch = three feet 1/36 = 0.0278 = 2.78 percent
Why fire does not comes downward?
The heat generated by the fire warms surrounding gasses and they rise, pulling the flame up.
What does a metal powder do in Pokemon?
Have a ditto hold it as an item and its defense will rise!
What is the rise of the cost of living from 2007 to 2014?
compare the cost of living in 2007 to the cost of living in2014
Does your marginal cost rise as you spend more hours supplying tutoring services?
Does your marginal cost rise as you spend more hours supplying services
What is the term used to describe the rise of low-cost newspapers in the 1830s?
A term used to describe the rise of low-cost newspapers in the 1830s is "penny papers".
How do you convert .25 inch per foot into degrees or percent slope?
To express .25 inch per foot as a percent slope multiply rise over run times 100. This can be expressed rise/run x 100. rise=.25 inch run=12inches. So .25 divided by 12 times 100 equals 2.083 which can be rounded to 2.1 or simply 2% slope
How does scarce resources give rise to opportunity cost?
The scarcer the resourse the greater the opportunity cost
What is the rise and run of stairs?
Stairs can be whatever you want them to be. It is usually a function of the room you have to work with and the elevation you are trying to bridge. 7 inch rise and 10 inch tread is very common.
