S
3
Hard to write that here but it is a capital S with the 3 slightly down below the S. i have tried a few times but cannot get this to work correctly. The 3 should be more to the right.
If you have the symbol for a regular switch, a 3-way switch is the same symbol with a '3' next to it like a subscript.
In electrical terminology it is known as a single pole double throw switch.
You need a three way switch to control lights from two locations. The name is misleading. Three way switch refers to the connection points on the switch. You can use a three way switch as a single switch as long as you place hot wire on the brass screw and the use any of the other screws for the return hot.
Each 3 way switch has 2 sets of contacts connected internally to a common pole (marked COMMON). Inside the switch are a set of normally closed (NC) and normally open (NO) contacts. Electrical normally closed contacts pass power unlike plumbing in which a normally closed valve blocks air or fluid flow.
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
If you have the symbol for a regular switch, a 3-way switch is the same symbol with a '3' next to it like a subscript.
electrical symbol
A three way switch is a switch that is used in a lighting circuit that allows the light fixture to be turned on from three separate locations within the building. In electrical terminology this switch is also referred to as a SPST, Single Pole Single Throw switch. The switch has three individual terminals of which two are always connected. These switches are usually located at the far extremes of the circuit with an intermediate switch between them. This intermediate switch is referred to an a four way switch.
A three way switch is a switch that is used in a lighting circuit that allows the light fixture to be turned on from three separate locations within the building. In electrical terminology this switch is also referred to as a SPST, Single Pole Single Throw switch. The switch has three individual terminals of which two are always connected. These switches are usually located at the far extremes of the circuit with an intermediate switch between them. This intermediate switch is referred to an a four way switch.
A three way switch is one of two devices that is used in operating a load from two different positions. This type of electrical circuit is known as three way switching. This terminology is used in North America, in Europe and the UK this type of switching is known as two way switching.
By changeover switch, if you mean forward reverse switch, the correct electrical terminology you should be searching is, wiring of an electrical drum switch.
A three way switch can be used as a single switch. Replacing this switch will not allow you to switch a fixture from two locations unless there is a three wire cable going to the second box.
In electrical terminology it is known as a single pole double throw switch.
You need a three way switch to control lights from two locations. The name is misleading. Three way switch refers to the connection points on the switch. You can use a three way switch as a single switch as long as you place hot wire on the brass screw and the use any of the other screws for the return hot.
a switch on railroad tracks
A two way switch is UK terminology for a North American three way switch. Though the switch has two names it is still a Single Pole Double Throw switch that has three terminals. North American terminology. The circuit is the same as the three way switch system. To control from four locations just add another intermediate switch. For the system to work properly the new intermediate switch has to be adjacent to the existing intermediate switch. The connections must run - three way, intermediate, intermediate, three way.
3 gang switch and you can call it 2-way switch..is a type of swithces we are using mostly in the stairs lighting ,that mean you have switch up to the stair and one down to the stair and you can switch the light on from one and switch it off from the other switch and via verse. <<>> There is no such thing as a three gang three way switch,. The nearest thing is a three gang double throw switch. It is used to supply a three phase load from two individual three phase supply sources. This is the type of manual switch that can be used for emergency power switch over from utility to generator. Three way switching uses a single pole double throw switch at each end of the circuit and a cross over switch in the center position. The center switch in a three way lighting configuration is a cross over switch and a double pole double throw switch in that position will not work.