0
All conduit shall not have more than 360 degrees for it's length between either a box, cabinet, or conduit body. Couplings count as a continuation of conduit.
Wiki User
∙ 19y ago
Add your answer:
Earn +20 pts
What is the take off for a half inch screwed 90 degree elbow?
1/2 inch
What is the degree of 0.18inch?
i think you. why? you are 0.18 inch engot.
What is the maximum weight capacity of a 1 inch thick by 6 inch width by 30 inch long plywood?
The answer will depend on what it is filled with - air or lead, for example.
What is the take off for a 26 inch 90 degree elbow?
39in.
How many 12 thhn conductors are allowed in half inch conduit?
9
When bending a 12 inch offset using 30 degree bends what would the distance between the two bends?
Use these numbers when bending offsets: 10 degree bends, multiply the depth of the offset by 6 this will give you the distance between bends. For 20 degree multiply by 2.6, for 30 degree multiply by 2, for 45 degree multiply by 1.4, for 60 degree multiply by 1.2. I use 30 degree bends for all of my offsets, just because its easier to do the math. So your answer would be 24 inches between bends. I have come to the conclusion anybody can bend conduit, its the measuring and marking that requires skill.
When bending a 12 inch offset using 30 degree BENDS what would be the distance between the two bends?
Use these numbers when bending offsets: 10 degree bends, multiply the depth of the offset by 6 this will give you the distance between bends. For 20 degree multiply by 2.6, for 30 degree multiply by 2, for 45 degree multiply by 1.4, for 60 degree multiply by 1.2. I use 30 degree bends for all of my offsets, just because its easier to do the math. So your answer would be 24 inches between bends. I have come to the conclusion anybody can bend conduit, its the measuring and marking that requires skill.
When bending a 12 inch offset using a 30 degree bend what would the distance between the two bends?
Use these numbers when bending offsets: 10 degree bends, multiply the depth of the offset by 6 this will give you the distance between bends. For 20 degree multiply by 2.6, for 30 degree multiply by 2, for 45 degree multiply by 1.4, for 60 degree multiply by 1.2. I use 30 degree bends for all of my offsets, just because its easier to do the math. So your answer would be 24 inches between bends. I have come to the conclusion anybody can bend conduit, its the measuring and marking that requires skill.
Using your finger how long is an inch?
From the tip of your pinky to where it bends in the middle
What is the maximum range of cal 38 revolver?
Depends to some degree on the barrel length. A 4 inch revolver has a maximum range of about 1000 meters- however, the maximum EFFECTIVE range is about 50-60 meters. That is the range where a shooter can reliably hit the target.
2 inch pipe how much flow?
There are way too many variables to answer this.what's the head pressure?how long is the run?any 90 or 45 degree bends?what type pipe?Pipe has friction , the longer the run the more pressure that is needed to get the same flow, same with bends in the pipe or fittings.For swimming pools we normally figure we can flow 60 gpm with 2 inch pipe.but again there are things to consider.
What is the maximum effective range 38 cal revolver?
This will depend to some degree on the barrel length. A 4 inch .38 Special revolver has an effective range of about 50-60 yards.
What is the maximum slope for 4 inch sewer pipe?
1/8th per inch
What is the maximum diameter of seamless pipe?
26 inch......means 650 mm
What is the maximum number of 8.5 x 11 inch sheets that can be cut from a 23 x 35 inch parent sheet?
Eight of them with some left over
What is the take out for a 4 inch 90 degree elbow?
6 inch or 4 inch if it's a short radius
What is the Hypotenuse of a 90 degree triangle with two nine inch sides?
The hypotenuse of a 90-degree triangle with two nine inch sides is: 12.73 inches.
