0
What resistance is necessary to operate a 3 amp device in a 12 volt system?
J1HASTY1W
(R) Resistance = (E) Voltage / (I) Current in Amperes
R = 12/3
R = 4 ohms
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What are the basic design requirements for a simple hydraulic or pneumatic device?
-your device must use hydraulics to exert a large force, using minimal space. - your hydraulic system must transmit motion smoothly. -you must be able to operate your device with no breakage of parts.
What type of system does potentiometer belong to?
Variable resistance.
What is the difference between 50N and 50G RELAYS?
50N: Instantaneous Earth Fault Relay50G: Instantaneous Ground Fault Relay50N is main EF protection device but 50G is standby as backup of main device.50N use for motor starters but 50G use for feeders.50N see zero sequence of EF current but 50N see residual current due to sum of three CT.If you have a resistance grounded system, a 50N may not see enough ground current to trip properly. If you do not have a resistance grounded system, a 50G may create nuisance tripping.
A device or circuit that provides power to the rest of the circuit or system is called what?
A device or circuit that provides power to the rest of the circuit or system is called a power supply,
What is meant by drivers in computers?
Drivers provide an interface between low level hardware (mouse, keyboard, printer, etc.) and the application software that uses them. Drivers normally operate within the operating system kernel, which is a protected area of the system. Poorly written drivers can cause full system crashes more readily than regular applications, since they have access to very important and sometimes complex parts of the system. Many a blue screen of death have been wrongfully blamed in Microsoft, when a poorly written 3rd party driver was at fault.
What is a system printer driver?
it is the software necessary for the printer to operate .
What is the software necessary for any computer to operate?
A system software or o.s
Why do you need to measure ground resistance value?
The whole point of earthing or grounding is to provide a low-impedance path back to the supply transformer in the event of an earth fault within a wiring installation, which will then enable sufficient earth-fault current to flow in order to operate the circuit's protective device (circuit breaker or fuse). When designing the circuit's protection system, it is therefore necessary to determine the resistance of the earth (ground) as it determines the value of this current.
What is a Warm Reboot?
After the device is attached to the system, the end-user may reboot the system without turning off power to the system. This is referred to as a warm reboot.The USB device, device driver, and application software must be able operate after the warm reboot.
What is Warm reboot?
After the device is attached to the system, the end-user may reboot the system without turning off power to the system. This is referred to as a warm reboot.The USB device, device driver, and application software must be able operate after the warm reboot.
What are the benefits of remote working system?
"Benefits of remote working system" -- It has less operational risks --Save time if it operated frequently --Operate from anywhere & make the device as portable
What are the basic design requirements for a simple hydraulic or pneumatic device?
-your device must use hydraulics to exert a large force, using minimal space. - your hydraulic system must transmit motion smoothly. -you must be able to operate your device with no breakage of parts.
How do you calculate absolute maximum current?
The absolute maximum current is used as part of a rating system, particularly for electronic components. It is a figure that a manufacturer will quote to indicate how much current can pass into or out of a device or a specific connection on the device. Exceeding that limit is likely to damage the device. The absolute maximum value is one that should never be exceeded but it is also normally higher than the maximum recommended current. The value is often measured during tests rather than calculated. The question might refer to the amount of current that might be drawn by a device. In this instance, to calculate the absolute maximum current that a device or component might draw there are two pieces of information needed. The first is the voltage that is applied to the device. The second is the lowest possible resistance that the device can have. Devices such as resistors, filament lamps and heaters have a constant resistance but active devices such as amplifiers, computers etc. can change resistance as they operate. It can be hard to find the resistance with some devices but once it has been established, Ohm's Law can be used to calculate the maximum current using the equation current = Volts divided by resistance. It is normally much easier to measure the current using an ammeter rather than trying to find the lowest resistance.
What is system manual?
A manual system is one you have to operate by hand.
What is system resistance?
The resistance the heart has to pump against
How do you operate a Bose av321 system?
To operate a Bose av321 system a media center must be used.
Is it necessary to have a Wii or other device to watch Netflix Movies?
You don't need any special system. You can watch Netflix movies on a normal computer.
