0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Do you use EMT or Rigid conduit in restaurant?
It depends upon the construction of the building as to what type of electrical system is used. If the building is of a wood frame then ordinary home wiring system can be used. If the use of steel studs is involved then BX has to be used for the internal wiring. Where the cables come out of the walls to equipment, they have to be mechanically protected with conduit or flexible conduit. If the building is block or brick and the wiring system has to be installed on the surface, the system has to be conduit. If the installation is not engineered and no stipulation as to what type of conduit system has to be used, then go with EMT. EMT systems are labour and material wise cheaper than a threaded rigid system. To make the job look professional you need to hire someone that is good at bending EMT conduit. Ask to see other jobs that the contractor has done before letting out the contract.
What do conduit connectors do?
A conduit connecter is a connecting piece used to connect two individual conduit units together. Conduit connecters can refer to both electrical conduits and pipe/plumbing related conduits.
What are the main principles concerning conduit bodies?
Conduit bodies are used to provide pulling access in a run of conduit, to conserve space where a full size bend radius would be impractical, to allow more bends to be made in a section of conduit or to split a conduit path into multiple directions.
What type of conduit is used for 480 volt 3-wire?
Conduit is just a medium to get the wires from one place to another. There is no voltage restrictions in low voltage wiring (750 volts or less). When it comes to conduit fill, electricians are governed by the electrical code conduit fill tables. The conduit is sized to accommodate the conductor size for a specific load.
Which one is cheaper PVC conduit or emt conduit?
PVC is cheaper but is used differently. PVC is usually baried in ground and emt usually runs exposed. You can use PVC exposed if it is schedule 80 gray PVC electrical conduit. Schedule 40 is for under ground
What kind of conduit does a 880 greenlee pipe bender bend emt or rigid?
A 770 Greenlee hydraulic pipe bender bend is used for rigid steel conduit from 2" to 4".
What is rigid conduit and where is rigid used?
There are two types of rigid conduit systems. One is PVC rigid conduit. It is mostly used in underground installations and in in areas that contain water or corrosive chemicals. The second type of rigid conduit is steel conduit. In Canada it is mostly phased out due to the high installation labour costs. Small installations are still used in small explosion proof areas.Both types of systems in Canada have been replaced with Tech armoured cable. Installation costs are lower and the wire is in the cable set, so no wires to pull. It is approved for above grade and underground direct burial installations. Tech also has been approved in explosion proof areas when used with the proper explosion proof end connectors to seal the cable.
What is another name for thin wall conduit?
There are many types of conduit used for the containment of electrical wires. PVC is a non-metallic option. If you need something that provides mechanical protection, EMT is a steel conduit with a thin wall. Need even more mechanical protection, you can use rigid conduit. It comes in steel or aluminum, and must be threaded together.
What is the purpose of a bender conduit?
A conduit blender is a tool that is used to bend conduit piping. This allows electricians to bend conduit piping around corners so that they do not have to use connector joints.
Another name for thinwall conduit is?
Another name for thin wall conduit is EMT and stands for Electrical Metallic Tubing. The term thin wall is used to differentiate between two conduit systems, thin wall and rigid conduit systems.
What are electrical conduit fittings used for?
An electrical conduit is a tube used to protect and route electrical wiring in a building or nonbuilding structure. Electrical conduit may be made of metal, plastic, fiber, or fired clay. Most conduit is rigid, but flexible conduit is used for some purposes.
What size rigid metal conduit should be used to house eight no 6 rh wires AND NINE NO 14 FEP wires?
2 inch
Do you use EMT or Rigid conduit in restaurant?
It depends upon the construction of the building as to what type of electrical system is used. If the building is of a wood frame then ordinary home wiring system can be used. If the use of steel studs is involved then BX has to be used for the internal wiring. Where the cables come out of the walls to equipment, they have to be mechanically protected with conduit or flexible conduit. If the building is block or brick and the wiring system has to be installed on the surface, the system has to be conduit. If the installation is not engineered and no stipulation as to what type of conduit system has to be used, then go with EMT. EMT systems are labour and material wise cheaper than a threaded rigid system. To make the job look professional you need to hire someone that is good at bending EMT conduit. Ask to see other jobs that the contractor has done before letting out the contract.
What size conduit should be used with 8-3 gauge wire?
Depends on location and local codes. typically plastic conduit or PVC is used outside or in wet locations. There are restrictions for PVC conduit. PVC can also be buried at a minimum depth of 24" There are a few types of metal conduit. EMT is used the majority of the time. The rigid pipe threads together and can be used in just about all locations. Then there is pvc coated rigid pipe which can be used anywhere provided you use the proper fittings. There are other types of conduit, such as fiberglass, aluminum and composites.
At what voltage do you need to use double locknuts on Rigid Metal Conduit?
There are no voltage regulations. A rigid conduit system used two locknuts and one bushing at every connection to a junction box unless the box has a hub. One outside the box and the other locknut inside the box. These are tightened against each other to make the connection secure and to scratch the paint on the outside of the box to make continuity of the metallic system. Continuity of the system is a must as this is the return path for any short circuit that might occur. Rigid connections to fittings require no locknuts as the conduit's threaded end screws into the fitting.
About multi threading in Java?
multi threading is used ,when we use no.of threads at one time the system will not support to run the multi threads ,in that case multi threading is used to solve the problem occured in threading multi tasking.
What are industrial electricians duties?
Industrial Electricians work in manufacturing plants, factories, power plants, ect. Rigid conduit is the usual raceway used, but also pvc coated rigid is common. also an industrial electrician will install and connect motors as well as motor control centers.
