0
What else can I help you with?
What does the abbreviation OC stand for when in follows a dimension?
On center.
How are surface datums different from axis and center plane datums?
When surface datums are shown on extension lines, they are offset from dimension line arrows. Axis datums and center plane datums, on the other hand, can align with the dimension line's arrowheads.
What is the name of the center of a circle?
The center of a circle is called the origin. It is a point at one end of a radius, the other end of which defines the circumference of the circle.
How do you calculate the distance between the center of cube and its vertices in 3 dimension?
By using Pythagoras' theorem.
How much can a twenty four inch load center forklift lift?
The load center of a forklift vehicle has little to do with its lifting capacity; this is determined by its structural engineering including the counterweight and pivot point. The lifting capacity of all forklift vehicles is stated on a tag on the vehicle, and is available from the manufacturer, and is also stated in the operation and safety procedures for the specific vehicle. The load center only tells you where you can place the load on the forks.
What is a dimension in Microsoft Word?
Dimension defines a specific measurement. A dimension in MS Word could be the width of a printed page.
What is voltage regulation of Transformer?
The change in output voltage from no load to full load defines the voltage regulation of that transformer.
What does the abbreviation OC stand for when in follows a dimension?
On center.
What circuit breakers can be used in a load center?
The same name breakers as the manufacture of the load center.
Can a lift truck with a 6000 lb capacity at 24 load center lift the load below with 30 load center?
No, a lift truck with a 6000 lb capacity at a 24-inch load center cannot safely lift a load with a 30-inch load center. The capacity of a lift truck decreases as the load center increases, meaning that the effective lifting capacity at a 30-inch load center would be lower than 6000 lbs. It's important to refer to the lift truck's load capacity chart to determine the specific capacity at different load centers.
What circuit breakers can you use in your load center and why?
Usually the load center and the breaker have to be of the same manufacturer to operate correctly.
Can a lift with a6000lb .capacity at 24 load center lift the following load?
To calculate whether the lift can handle a specific load, you need to know the weight of the load and the load center. If the total weight of the load is less than or equal to 6000 lbs and the load center is 24 inches or less, then the lift should be able to handle it. If the total weight exceeds 6000 lbs or the load center is greater than 24 inches, the lift may not be able to lift the load safely.
What is the problem of operating a on-load furnace transformer with center tap?
What is the problem of operating a on-load furnace transformer with center tap
What dimension determines the stroke of an engine?
The distance from Top Dead Center to Bottom Dead Center of piston movement.
If a shaft is supported at both ends and the shaft is deflected X dimension at center span by a given load while static What will happen to the X dimension if the shaft is rotated at 1000RPM?
It depends (note, this is the correct answer to all engineering questions :) ) IF the shaft is correctly designed for the load and speed, then nothing will happen. That is, X will stay basically the same in magnitude and direction. However, if the shaft is too flimsy, then it could become unstable as the speed increases and "whip out" and fail completely.
Does the load capacity on a forklift increase or decrease as the load center moves farther away from the base of the carriage?
The load capacity of a forklift decreases as the load center moves farther away from the base of the carriage. This is because as the load center moves outward, it creates more leverage and increases the force exerted on the forklift, which can exceed its rated capacity.
What is the exact point on which an entire load will balance on a forklift?
The exact point on which an entire load will balance on a forklift is the center of gravity of the load. This point is where all the weight of the load can be considered to act, allowing for optimal balance and stability on the forklift.
