You should not exceed 80% of the breaker rating for a continuous load. Therefore, the continuous load should not exceed 16 amps.
Yes, the amp rating is a measurement of the highest amp load it should carry. So a 15 amp appliance will work on a 20 amp socket but you wouldn't want to use a 20 amp appliance on a 15 amp socket.
Yes you can as long as it is feed off of a 20 amp circuit in at least #12 gauge wire.
Yes, you can use lower amperage outlets - the problem would come if you were trying to run a 20 amp appliance on a 15 amp circuit or plug a 20 amp appliance into a 15 amp outlet. It would be better, though, as some kitchen appliances could exceed 15 amps (toaster ovens, some coffee makers, electric griddles, etc.) could try to draw more than the 15 amps your outlets are designed for. Perhaps you could get some 20 amp outlets and use those 15's in a hallway or something less likely to have high amperage draw.
80% of the rated circuit. 10 amp circuit is 8 amps, 20 amp circuit is 16 amps, etc.
You should not exceed 80% of the breaker rating for a continuous load. Therefore, the continuous load should not exceed 16 amps.
Yes, the amp rating is a measurement of the highest amp load it should carry. So a 15 amp appliance will work on a 20 amp socket but you wouldn't want to use a 20 amp appliance on a 15 amp socket.
Yes you can as long as it is feed off of a 20 amp circuit in at least #12 gauge wire.
Yes, you can use lower amperage outlets - the problem would come if you were trying to run a 20 amp appliance on a 15 amp circuit or plug a 20 amp appliance into a 15 amp outlet. It would be better, though, as some kitchen appliances could exceed 15 amps (toaster ovens, some coffee makers, electric griddles, etc.) could try to draw more than the 15 amps your outlets are designed for. Perhaps you could get some 20 amp outlets and use those 15's in a hallway or something less likely to have high amperage draw.
Yes, if properly wired a 20 amp circuit is a great circuit for an 18 amp appliance. Properly wired means you've used 12 gauge wire or larger and the circuit is protected by a 20 amp breaker or fuse and all connections are secure.
80% of the rated circuit. 10 amp circuit is 8 amps, 20 amp circuit is 16 amps, etc.
You can and it will work as long as the circuits load remains below 10 amps. Any load amperage over 10 amps will continue to blow the smaller size fuse.
You would need a 20 amp switch when the load controlled by the switch can draw as much as 20 amps. If you have a 20 Amp breaker supplying the circuit then you need to size all switches and outlets on that circuit to 20 amps.
5. You are probably asking about wire size. 15 amps is typically 14 AWG and 20 amps is 12 AWG.
You can use the wire rated for 20 amps on a 15 amp receptacle but you can not use a 20 amp fuse on any device rated at 15 amps. This is a tricky part of the code about receptacle outlets, You can use a 15 amp duplex outlet on a 20 amp circuit. (duplex outlet two devices can plug in) If it is a single outlet then the outlet must be rated 20 amp. NEC table210.21(B)(3). ============ A 15 amp duplex receptacle can be wired to a 20 amp rated circuit. This means the breaker OR fuse protecting the circuit can be rated 20 amps if the wire is also rated at 20 amps (12 AWG). --Sparkfighter
A 20 amp circuit be used for any device that takes up to 20 amps to make it operate.
If the appliance is just to be plugged into a circuit with multiple outlets then you just need to make sure that the sum of currents for all devices on the circuit are less than the rated current. A rule of thumb is total current should be no greater than 80% of the rated current. So you might have a 20 A breaker and several 2.5 A appliances on this circuit. If you have a dedicated circuit for the appliance you would only need to size the breaker for the maximum current being drawn by the appliance. If the appliance contained a motor then there might be a start-up current that might be as high as 15 amps so you would likely go to a 20 amp breaker for a safety margin. As a practical matter a dedicated circuit for an appliance in the 2.5 amp range should have a 15 amp breaker. I always install a 20 amp breaker just for added margin and possible future applications.