0
You have an outlet with three light switches controlling three different lights what is this called?
Wiki User
∙ 16y ago
A triplex outlet. It is a simple device unless one or more of these switches are "3way" switches.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you get all of the light switches to be in the down position for off when you have more than one switch for them?
Three way switches do not have a up-on down-off position. With the lights off, reposition the switches so that the handles are all down. This is the start position and depending on how you enter the room and turn on the lights certain switches will be left up when you leave the room. That is just the design of the switches and for the asthetics of the look, all handles down the lights will be out.
How do you install a dimmer switch for multi fixtures where the original switch has 2 black wires and one red with no green?
This simple if you have two switches controlling a set of light you will need to buy a three way switch. A three way switch will have a place for three connection. Depending on what brand of switch you purchase the directions will be sightly different but most dimmer come with detailed directions and diagrams. When you by a dimmer you need to read what kind of load it is meant to control. They are built to control incandescent light, magnet low voltage lights or electronic lights.
Can you use 10 3 wire for outlets and lights in a home?
You could but is it a total waste of money and is overkill. Use 12/2 with ground on all 120 volt outlets and light switches.
How do you control 4 light in one switch and the same lights control by 4 switches?
You want four switches to independently turn 4 lights on and off. You need two 3-way switches, and two 4-way switches. The first 3-way is located where the power first comes into this system, two travelers (wires) go to the first 4-way switch, two travelers then go from that switch to the other 4-way switch and two wires go to the final 3 way switch. The third wire on the last 3 way switch then goes to the first light fixture. This is a complicated wiring project and it is not as simple as it sounds. Realistically, you will have more than 2 wires traveling between switches depending on whether the neutral is located, and further more dependent on whether power from the panel first comes to a switch or to a light fixture. You need to plan this well or you may have more wires in one or more boxes than code allows. Also, wires must be attached in particular positions on all the switches, or you will end up with a situation where some of the switches will work and some won't and troubleshooting is very complex.
What is electrical supply timer?
Hard to know what you are meaning? A timer is a device in a circuit that switches on then off at given times. There may be many on/off operations not just the one. Think of some lights, say street lights that come on at a certain time then off at a later time. If they are electric that would fit you question. Although the lights are more likely controlled by darkness at dusk and first light in a morning. G4CIR
Where is the switch to turn off interior door lights?
should be with the head lights as an alternate switch or in combination with headlights, move switches in different combinations to see if you can get them to turn off
Do I need a GFCI for lights in the garage?
no. as long as the lights or switches for those lights are not out in the wheather and cann't get wet.
Can you use sensor lights like normal toggle switches?
If you attach then to normal switches as well as the centre
How do you turn off the dome lights in a Ford Taurus wagon?
depending on the year the Taurus lights will either have switches on the sides, or the switch is made into dash dimmer switch. If these switches wont turn the lights off, check the doors to make sure that the door switches operate properly.
How do you get all of the light switches to be in the down position for off when you have more than one switch for them?
Three way switches do not have a up-on down-off position. With the lights off, reposition the switches so that the handles are all down. This is the start position and depending on how you enter the room and turn on the lights certain switches will be left up when you leave the room. That is just the design of the switches and for the asthetics of the look, all handles down the lights will be out.
Interior lights are alway on jeep?
Check all the door and light switches, they are turned on by twisting the light switch to the left, also the pin switches on the doors will activate the cabin lights.
Why was Benjamin Harrison afraid of electric lights?
It wasn't the lights he was afraid of. He was concerned that touching the switches that controlled the lights would electrocute him - and he often slept with the lights on.
What are the parts of a Stereoscope?
Binoculars, objective, lights, light switches & stage
Are light switches required on all lights or are pull strings allowed?
A pull-string or pull-chain switch IS a light switch. Some other types of light switches are called wall switches and cord switches.For more information see the answers to the Related questions shown below.
Does a double-pole switch control lights from two locations?
No. A double pole switch would be a switch that switches 2 different loads simultaneously. 3-way switches (and 4-way switches if more than 2 are used) are what are used for controlling a light from multiple locations. While a typical single pole switch simply opens or closes a single contact, a 3-way switch provides a path from a contact point to, let's say, point A or point B. Points A and B from the first 3-way switch are connected to points A and B of the second 3-way switch and then the common contact point of the second switch is connected to your light. When more than 2 switches are desired, you can use any number of 4-way switches between the 3-way switches, but the 3-way switches MUST be on the ends of the circuit.
Where are the door switches for the interior lights on a 1999 Mondeo 2l Ghia?
The design is different on the post 1997 mondeos, the light switches are controlled by the lock on the B & C pillars. There is a rubber switch behind the loop that the lock engages with. email@bigstoop.co.uk mondeosport.com
Where would you find series circuits?
-- Older/cheap Christmas lights.-- Switches for lights and other household appliances, but not the household outlets.
