Best Answer

Scroll down to related links and look at "Inches and centimeters in comparison".

Q: You want to see a ruler with inches and centimeters?

Write your answer...

Submit

Still have questions?

Continue Learning about Math & Arithmetic

3.937007874 inches. See formula with complete algebraic steps below: 10 centimeters*1 inches 2.54 centimeters=3.937007874 inches

See if you can find a part of the ruler where there are 9 little marks between the inch divisions: that section of the ruler may be marked as "10ths" or "TENTHS". Each of the gaps between these marks is 0.1 inch so you want 8 gaps.

12 u can see it is clearly labeled on most rulers the number of inches theere are

According to the U.S. Treasury web site at (See related link below for website), all current U.S. currency is "approximately 2.61 inches (6.63 centimeters) by 6.14 inches (15.60 centimeters)".

Reading a Ruler is very easy. This is only if you are using whole numbers for inches and centimeters. here are a few easy steps on how we can read the ruler. 1. There are 2 different measurement systems in rulers. English and Metric. If you don't find the sides to be labelled, its easy to make out which side is inches and which side is centimeters just by looking between the lines. 2. Now if you watch it, you will find 9 lines between each centimeter that make up one millimeter. So naturally 10 millimeters would make up a centimeter. This is useful in terms of metric calculation. 3. If its inches, the number of lines would be seven instead of 9. So depending on what system you want to use is makes up your reading of the ruler. If you are using Metrics, use centimeters or if you use English, use inches. 4. When starting to measure, see that your start and end points are perfectly placed. Also take note of the points. The later point is what makes up the measurement. 5. Suppose you end up on not a whole number, say you are using centimeters as preferred choice of measurement i.e metric system. You start to measure and you end up at a non whole number such as 5 lines after 3 number, then your measurement would be 3.5 centimeters i.e 3 centimeters and 5 millimeters. For more info, please refer the link in sources. Hope this helps.

Related questions

You have to take a ruler and line it up VERY strait then see how many centimeters/inches it is then you see what number it is!

It depends on the size of the bucket. Use a ruler or measuring tape to see how many inches (or feet, or centimeters, or millimeter, ect. ) deep or wide it is.

3.937007874 inches. See formula with complete algebraic steps below: 10 centimeters*1 inches 2.54 centimeters=3.937007874 inches

See if you can find a part of the ruler where there are 9 little marks between the inch divisions: that section of the ruler may be marked as "10ths" or "TENTHS". Each of the gaps between these marks is 0.1 inch so you want 8 gaps.

The straightedge can only be used to draw a straight line, or check to see if a surface is flat, but cannot measure length. A ruler can be used to draw a straight line or check for flatness, and a ruler can also measure length because it has evenly spaced markes denoting inches and centimeters.

You can use Google.com as a calculator for conversions. Enter "5 feet 2 inches in centimeters", and you'll see that the answer is:

12 u can see it is clearly labeled on most rulers the number of inches theere are

There are 2.54 centimeters in one inch. Therefore to get amount of inches in centimeters, value of centimeters has to be divided by amount of centimeters in one inch: 60 centimeters = 60 / 2.54 = 23.622 inches

You cannot see 9.44 inches on a ruler. The inches are often - though not always - marked in tenths. 9 inches will be shown on the ruler. From there move four small units towards the 10 inch mark. That is 9.4 inches away from the 0. Slightly less than half a mark further along is 9.44 inches.

You need a ruler, tape measure or something else preferably graded in inches, then you put this against what it is that you want to measure and see what you get. If your measuring device is graded in cm remember that 1 inch is 2,54 cm

Conversion formula: cm x 0.393 = inchesFor more accuracy, if needed, use 0.393700787 as the conversion factor.Algebraic Steps / Dimensional Analysis Formula____ cm*1 in2.54 cm=? in

The first (or smallest measurement) you would see is the hash marking millimeters, which is written as "mm". 1mm equals the thickness of a dime. The unit of measure that is most often displayed on a metric ruler would be centimeters written "cm". 10mm equals 1cm and 2.5cm is about equal to 1 inch. Centimeters are displayed for viewing like inches are, marked on the ruler in increments of 1, 2, 3, 4... and so on. Usually to 30cm which is slightly less than 12 inches