0
You have both a mechanical and electrical issue. From a mechanical standpoint you need the switch mounted securely in the fixture. The switch will have two black wires or two terminals. You need to insert the switch in series with the black wire going to the fixture. Let's say that the black wire from a supply is connected to the black wire in the fixture with a wirenut. Undo the two wires and connect each wire to a wire on the switch.
What else can I help you with?
How do you connect an ON-OFF switch to control the light?
To control a light with a switch, the switch has to be connected in series with the light fixture.
Can a pull chain light switch be converted to wall switch?
The pull chain on the porcelain light fixture can be converted to a wall switch very easily. You will need to install a new two wire #14 cable from the box the fixture is mounted to now to the new wall switch box. Remove the power to the circuit by shutting that circuit's breaker off. The wire that is connected to the switch in the light fixture is the incoming "hot" wire. Disconnect it and re connect it to the black wire that goes down to the switch. Disconnect the white wire from the old porcelain fixture. For the installation of the porcelain fixture connect the white wire to the silver screw on the new fixture. Now connect the white wire that returns from the switch to the brass coloured screw on the new fixture. Mark this white wire with a small piece of black electrical tape to re identify it as not a neutral (code rule) but a potential "hot" wire. At the switch end make sure that the black wire is connected to the top screw and the re identified white wire (with a black tape marker) is connected to the bottom screw of the switch. Connect the ground wire in the cable to the new switch box and the existing fixture box. Install the switch making sure that the switch is in the off position and that the handle in facing downwards. Install switch plate cover, turn the breaker back on and you are finished. This project is relatively easy to do if there is already an existing wall box close to the pull-chain switch BUT ONLY if it already has the right wiring in it.If there is no such wall box then a new one will have to be installed and wired. If you already know how to do that safely you would not be asking this question here!For some relevant information, please see the related question below about replacing a wall switch by a pull switch. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Can you convert a flush mount light fixture to a pendant light fixture?
Yes. The Home Depot has a kit for about $10 that converts a recessed can to accept a standard fixture. Weight limit is about 10 pounds.
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
How do you wire a fixture that had two hot and two neutral wires?
To install a new fixture to replace the one that was removed reconnect the two hot wires together and then reconnect the two neutral wires together. Place the two wires from the new fixture to the corresponding wire colours that you just spliced together. This wiring should be down stream from the light switch. When the switch is turned on the new fixture should light. If this is not the scenario of your question then more information needs to be given.
Have a bathroom light that is wired hot at all times how do you wire a pull chain up to it?
To wire a pull chain to a bathroom light that is constantly hot, you would typically connect the hot wire from the light fixture to one terminal of the pull chain switch and then connect the other terminal of the pull chain switch to the hot wire in the electrical box. Make sure to turn off the power supply before making any electrical connections for safety. If you are unsure, it is best to consult a licensed electrician.
How do I replace a broken pull chain on a light fixture?
To replace a broken pull chain on a light fixture, you will need to turn off the power to the fixture, remove the old pull chain switch, and install a new one by connecting the wires according to the instructions provided with the new switch.
Can you connect a wall switch and a light fixture to an existing light fixture?
Yes, you can connect a wall switch to an existing light fixture by running a new electrical wire from the switch to the fixture. This allows you to control the light fixture independently of the existing fixture. It is recommended to consult a licensed electrician to ensure proper wiring and installation for safety.
How can I switch the light fixtures in my bathroom?
Switching a light fixture requires the following steps. First, remove the old fixture. Second, you must disconnect the wiring. Third, a junction box must be installed. Finally, a new fixture must be installed. Detailed instructions can be found here: http://www.diynetwork.com/how-to/replace-a-bathroom-light-fixture/index.html
How do you wire a pull switch on a hard wire ceiling light that has no switch?
Two options. Change the fixture to a keyed pull-chain, or add a pull-chain adapter to the existing fixture. Both available from Home Depot and others for about $3.
How does a pull chain light work and what are its main features?
A pull chain light works by using a chain that is connected to a switch inside the light fixture. When you pull the chain, it activates the switch, turning the light on or off. The main features of a pull chain light are its convenience in easily turning the light on and off without the need for a separate wall switch, and its simple and traditional design that is commonly found in older homes or in areas where a wall switch is not practical.
Why don't bathroom ceiling light go on or off when there is voltage coming from the switch to the fixture?
This could be due to a faulty light fixture, a wiring issue, or a problem with the switch itself. It is recommended to check the wiring connections, test the switch, and if necessary, replace the fixture if it is damaged. If unsure, it may be best to consult a licensed electrician for proper diagnosis and repair.
What are some important factors to consider when choosing a bathroom light fixture?
When choosing a bathroom light fixture, consider factors such as the size of the space, the amount of light needed, the style and design of the fixture, the type of lighting (warm or cool), and the placement of the fixture for optimal illumination.
How do I install a bathroom light fixture?
To install a bathroom light fixture, first turn off the power to the existing light fixture. Remove the old fixture and disconnect the wires. Install the new fixture according to the manufacturer's instructions, connecting the wires and securing the fixture in place. Finally, turn the power back on and test the light to ensure it is working properly.
How can I install a bathroom light fixture?
To install a bathroom light fixture, first turn off the power to the existing fixture. Remove the old fixture and disconnect the wires. Install the new fixture by connecting the wires and securing it to the wall or ceiling. Finally, turn the power back on and test the light to ensure it is working properly.
How can I ensure a successful installation of a bathroom light fixture?
To ensure a successful installation of a bathroom light fixture, follow these steps: Turn off the power to the bathroom at the circuit breaker. Remove the old light fixture and disconnect the wires. Install a mounting bracket for the new fixture. Connect the wires of the new fixture to the existing wires, matching the colors. Secure the fixture to the mounting bracket. Turn the power back on and test the light. Make sure the fixture is securely attached and functioning properly.
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
