0
The National Electrical Code allows this change only if you upgrade the whole circuit. BUT ..If you are using this outlet only when the light is on, connect the black wires together and the white wires together. Ground wires together to the box also. IF THIS IS WITHIN 6 FEET OF A WATER SOURCE, IN A BASEMENT, GARAGE, OR OUTSIDE IT HAS TO BE GFI PROTECTED!!!!
Wiki User
∙ 19y ago
Wiki User
∙ 14y agoIn the outlet, as a general rule,
The Black is the power
The White is the neutral (Which is alot like ground)
The copper is Ground. (In fixtures, ground is sometimes green)
As a general rule, a fixture has a black power and a white neutral.
There are YouTube videos that will teach you about house wiring.
Wiki User
∙ 14y agoWiring a 2 wire fixture to 4 wire outlet depends on configuration of wires in outlet box.
If you have 2 white and 2 black I will assume there are more lights controlled by the same switch.
1st scenario attach both black wires to black of 120 volt fixture. Attach both white wires to white wire from fixture. atach ground to box or ground wire.
2nd scenario attach white neutral to white from fixture, Attach black hot to white going to switch. Attach black from switch to black from light Fixture.
If you need further help I recommend hiring a contractor. Take a look into contraxtor.com
Wiki User
∙ 11y agoThe NEC allows you to replace a 2 wire receptacle with another 2 wire receptacle. Replacing it with a 3 wire receptacle requires you to rewire the circuit with 3 conductors or install an additional ground wire run with the existing 2 wires.
It is bad practice to connect the neutral to both the neutral terminal and the ground terminal. It creates a potential hazard you want to avoid. Some would install the 3 wire recept without any connection to the ground terminal. This is best if you have no other option but it is then easy to forget, or for someone else not to know, that there is no grounding connection to whatever you plug in. This is a code violation.
Wiki User
∙ 11y agoAnswer for UK, Europe and countries running a 50 Hz supply service.
Connect the brown wire on your 2 wire cord to the live i.e the left pin on your three pin plug and the blue one on the neutral which is the pin on your right. But, for safety reasons, the device being powered through the 2 wire cord must be double insulated since then it won't need an earth wire.
Wiki User
∙ 16y agouse both wires to hook up black and white..u must use the ground wire also ground the ground wire to the socket your installing..then your ok
Wiki User
∙ 16y agoyes
Add your answer:
Earn +20 pts
How do you connect a 3 wire fixture to a 2 wire fixture that are connected to the same switch what do you connect the red wire to?
A three wire fixture most likely is one that has two separate loads within it. An example is a ceiling fan with a light fixture. If the three wire is used to separately switch the two loads you have to make a decision as to which load you want to work with the two wire fixture. Once that decision has been made connect the two wire fixture in parallel with the your selected load on the three wire fixture. On these types of installations the three wire fixture is usually controlled by two separate switches in a two gang box. The red and black wires of the three wire terminates on the bottom of either switch. The white wire is connected to the incoming neutral. The top of the switches are paralleled together with the "hot" feeder from the distribution source.
How do you add another porch light to an existing switch?
Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
What does a two phase outlet look like?
it is Outlet that will work with 2 hot wire one black and white.
How do you connect 3 wire to 2 wire 240volt's I'm trying to remove the washerdryer outlet and branch four 240v receptacles from the 240volt 3 wire outlet?
just leave the neutral wire as it is and connect the other two !!
How do you connect a 3 wire fixture to a 2 wire fixture that are connected to the same switch what do you connect the red wire to?
A three wire fixture most likely is one that has two separate loads within it. An example is a ceiling fan with a light fixture. If the three wire is used to separately switch the two loads you have to make a decision as to which load you want to work with the two wire fixture. Once that decision has been made connect the two wire fixture in parallel with the your selected load on the three wire fixture. On these types of installations the three wire fixture is usually controlled by two separate switches in a two gang box. The red and black wires of the three wire terminates on the bottom of either switch. The white wire is connected to the incoming neutral. The top of the switches are paralleled together with the "hot" feeder from the distribution source.
What are my options for plumbing fixtures with more than one inlet and outlet?
A tee is a plumbing fixture with one inlet and two outlets, or two inlets and one outlet. A cross is a fixture with one inlet and three outlets, or three inlets and one outlet.
Can one convert a two prong outlet to a three prong outlet?
Yes, provided that you have a ground wire in the box and that the ground wire is properly connected in the electric panel.
How do you connect a White Black Green wired device to household White Black Red ground light outlet?
If there is a red wire in the fixture box it sounds like the fixture is three way switched. The travelers are coming from one of the two switches and the cable is going to the second switch.See related links below.
How do you wire in a pull chain switch in a bathroom light fixture?
If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.
What type of prewire for a ceiling fan light?
The pre wire for a ceiling fan light should be made with a three wire cable. This cable will have a red, black, and white wire as main conductors. This cable will also have a bare ground wire. This wire should be strung between a two gang switch box to the fixture junction box. This pre wire allows the supply to be either fed to the two gang box. From the two gang switch junction box, one side will be used for the light in the fixture and the other side of the switch junction box, itwill be used for the fan portionin the fixture.
What is single phase outlet?
It is an outlet that has one hot wire, such as a household receptacle, or two hot wires, such as a dryer outlet (in the US). If the outlet has three hot wires, it would be called a 3-phase or polyphase outlet. These would normally be found only in an industrial setting.
How do you add another porch light to an existing switch?
Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
How do you wire a fixture that had two hot and two neutral wires?
To install a new fixture to replace the one that was removed reconnect the two hot wires together and then reconnect the two neutral wires together. Place the two wires from the new fixture to the corresponding wire colours that you just spliced together. This wiring should be down stream from the light switch. When the switch is turned on the new fixture should light. If this is not the scenario of your question then more information needs to be given.
What is meant by 220 volts AC?
In US household electrical service there are two "hot" 110 volt wires and one ground. Only one hot wire is connected to a normal outlet or light fixture. To wire a 220 volt alternating current outlet, both hot wires are connected to the outlet. This is used for appliances that need more power than is provided by 110 volts like electric ranges, clothes dryers, air conditioners.
What does a two phase outlet look like?
it is Outlet that will work with 2 hot wire one black and white.
