Splice a new green wire to extend it, using the same size gauge of wire. Do not use wire nuts, use a proper electrical connector with grub-screws which can be securely tightened-up. <><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
The simple answer is, it doesn't.
This is not a serious problem, if you ensure that the fixture is wired properly.
Make sure the line conductor (black wire) is attached to the terminal at the bottom of the socket, and the neutral is attached to the outer (screw part that holds the bulb) conducting casing.
==================
I agree with the above answer in that when there is no grounding conductor provided in the box, the ground wire for the fixture is very often ignored. The fixture will work fine without it.
HOWEVER, if there should ever be a fault develop between the hot wire and the metal of the fixture, the metal of the fixture is energized and WILL NOT trip a breaker. This is the purpose of the ground wire. It is a violation of code. And over time with dust, Spiders, water, and other foreign objects collecting in the fixture you are more likely to develop a fault. The third wire is for your protection.
One of the most common ways faults such as these occur is when trouble-shooting or replacing a fixture. If the circuit is energized, moving the fixture around to check it or replace it can bring the hot wire into contact with the metal of the fixture, which may very well be in your hand.
you can ground it to the fixture electrical box.
body of fixture
Through above ground/below ground power lines.
Ground level carbon dioxide is a pollutant. It reaches to atmosphere by westerly's.
You use a known ground and check them for voltage. You can use an extension cord to reach from a ground to the wires you are testing. You are not putting it in an outlet, just to connect you to a ground.
because its not a giraffe and its neck cannot reach the ground unless it bends down
They use their roots to reach ground water, and use that water for photosynthesis.
The ground or Earth plate is in Mt. Coronet on the west side of Oreburgh City. It's downstairs and you need HM Surf to reach it.
AnswerThere are two screws for each bulb fixture. Get down on the ground and you'll see them at the tag light. They are 7mm screws. Unscrew them til loose. You don't have to take them off all the way. After unscrewing them, slide lighting fixture away from bumper, and twist the bulb to the left, and pull it out. The license plate light bulb size is 194. You will probably have to take off the license plate in order to reach the bulb fixtures.
Grounding a Vehicle BatteryUsually, manufacturers attach the ground cable from the battery to the engine block. I don't change that unless some other factor makes using the manufacturer's ground location impossible, and then I route the ground cable to a manifold bolt within reach of the cable.
Precipitation that does not reach the ground is called 'virga'. If it does reach the ground, it's called 'praecipitatio'.
Open the hatch. Right behind the light fixture that contains the bad bulb is a cover plate inside the trunk. Remove it and reach inside. You'll find two big plastic nuts that hold the fixture in place. Remove both (they turn with the hand) and push the fixture out of the fender. Unhook the wire to the bulb, twist the socket to get it out, change the bulb, put the socket back in and reconnect the wire, put the fixture back in, put the nuts back on and replace the cover.
Open the hatch. Right behind the light fixture that contains the bad bulb is a cover plate inside the trunk. Remove it and reach inside. You'll find two big plastic nuts that hold the fixture in place. Remove both (they turn with the hand) and push the fixture out of the fender. Unhook the wire to the bulb, twist the socket to get it out, change the bulb, put the socket back in and reconnect the wire, put the fixture back in, put the nuts back on and replace the cover.
In vacuum they reach ground exactly at the same time. In a medium other than vacuum the ball will reach ground first.
Ground water is on or in the ground, it does not reach it.
Well, the trunk of the willow clearly touches the ground ;) but yes, willow tree branches can reach the ground, and old willows' branches often do.
The ball which you drop from 5 feet will reach the ground first.
Meteorites
Yes and no. The funnel of a tornado does not have to reach the ground for damaging winds to occur at ground level. However, if those winds reach the ground then the tornado has touched down even if the funnel hasn't.