hola tengo un auto estereo kenwood kdc-x589 pero cuando incerto el cd me aparece la leyenda E-05 cual es el problema?
Press the source button until standby appears then hold the menu button until clck appears. Then press and hold the toggle knob on the right until the clock adjustment appears. Up and down is for hours and left and right is for minutes. Press the source button and your all done
Kenwood Security Code Over Ride
Must use a remote with Letters and a Numbered key pad All Excelon CD receivers have the correct remote
Head units with a Rotary Volume control Knob:
Press and hold the Auto button.
While holding the Auto button, push and hold the Track Up button. The "_ _ _ _" will disappear after about 5 sec.
Enter KCAR using the <"Arial, sans-serif">remote control from a higher end CD Receiver or any Excelon CD Receiver.
Enter "KCAR" with the remote controller as described below.
"K": Press TRACK UP key (>>|) after pressing 5 key twice.
"C": Press TRACK UP key (>>|) after pressing 2 key once.
"A": Press TRACK UP key (>>|) after pressing 2 key three times.
"R": Press TRACK UP key (>>|) after pressing 7 key twice.
* If you commit a mistake in the code entry, the unit enters the
code request mode again.
Press the Track Advance button on the remote to enter the override code.
The unit will enter the All Off or Standby mode if done properly.
Video Unlock:
Use a remote from a higher end CD Receiver or any Excelon CD Receiver. Some Video remotes will work, switch on remote must be set to AUD.
Press 55222277 on the remote. There will be NO visual verification when entering the override code.
Head units with a Up / Down Volume control buttons:
Press and hold the Volume Up button.
While holding the Volume Up button, push and hold the Disp button. The "_ _ _ _" will disappear after about 5 sec.
Enter KCAR using the <"Arial, sans-serif">remote control from a higher end CD Receiver or any Excelon CD Receiver.
Enter "KCAR" with the remote controller as described below.
"K": Press TRACK UP key (>>|) after pressing 5 key twice.
"C": Press TRACK UP key (>>|) after pressing 2 key once.
"A": Press TRACK UP key (>>|) after pressing 2 key three times.
"R": Press TRACK UP key (>>|) after pressing 7 key twice.
* If you commit a mistake in the code entry, the unit enters the
code request mode again.
Press the Track Advance button on the remote to enter the override code.
The unit will enter the All Off or Standby mode if done properly.
kenwood car stereo kdc-mp528 wiring diagrahm
unlock codes for ken kdc-mp435uwood
I noted that on www.technologz.com a Kenwood radio was unlocked using the KCAR code. Here is how it was dome:
Here are the steps of unlocking a DPX-8070MJ radio player:
(1) Press and hold the 1 and then the 6 preset key. There are 6 preset keys or buttons on the face my radio on the left side. The radio will display a "C" just after the "CODE****"
(2) You now need to enter the code "KCAR" using a Kenwood remote control (The remote control for my radio is RC-600J). Point your remote towards the radio
(3) Press Numeric Key "1" until the letter 'K' is displayed
(4) Press Numeric Key "2" until the letter 'C' is displayed
(5) Press Numeric Key "3" until the letter 'A' is displayed
(6) Press Numeric Key "4" until the letter 'R' is displayed
(7) Press "Ent" button on your radio and YOUR RADIO WILL BE WORKING AGAIN
You can download the instruction manual from Kenwood.com. The wiring diagram is on page 29.
if you dont have a remote for your unit you need to get one. Once you have the remote type in this code.
55222277. The unit wont look like its doing anything at first, but it should work.
The memory wire is blue on the Kenwood VZ907. Now I hope you can help me. I am trying to hook this same product in my vehicle. However, I cannot get past BUS-E50. What does this mean? The memory wire is blue on the Kenwood VZ907. Now I hope you can help me. I am trying to hook this same product in my vehicle. However, I cannot get past BUS-E50. What does this mean?
Hold down the menu button for 5 sec then move the FM button right it should say AUX off then move it down for ON
* Use the SRC button to put the radio into STANDBY mode. Screen should show STANDBY. * Press and hold Menu button for two seconds. * Use the joystick control to scroll up or down until you see DEMO ON.
* Press the joystick in for two or three seconds. Screen should show DEMO OFF.
The manual says to push the joystick left or right, but that is incorrect.
i wouldn't worry about the wiring diagram, just remember that usually, red is power, black is negative, and green or brown is usually earth. youll have no trouble with fiddling with it, give it a go, no harm done.
Red - +12v Ignition/Switched
Yellow - +12v Battery/Constant
Black - Chassis Ground
Blue - Power Amplifier
Blue/White - Power Amplifier Remote
+++++++++++SPEAKERS+++++++++++
Green - LR+
Green/Black - LR-
Violet - RR+
Violet/Black - RR-
White - LF+
White/Black - LF-
Grey - RF+
Grey/Black - RF-
I blew an engine fuse on my Miata and my Kenwood KDC-X859 went into the theft security mode when I reconnected it to power. After a lot of research and trial-n-error I was able to reset the code. I put the entire process and all of the useful links on my blog:
http://techbybucky.blogspot.com
-Bucky
no you cant. only when using ipod/iphone or dvd