0
15000ppsi and we had a twenty percent rise in viscosity what would potentially our new peak pressure at transfer be?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the significance of Pascal's Law?
It is basic of hydraulic and pressure transducer design. Break fluid work on the principle of pressure transfer in confined space. Pascal's law contribute greatly to physical science e.g. field of Fluid dynamic and Thermodynamic.
If you were to transfer a liter of air into a 2-liter container how much of the 2-liter container would be filled?
0
When do you use a diaphragm seal What is the process of measurement and control?
Process measurement sensors are not indestructible. Not even the most rugged device is fully immune to the chemical nature of process media or the kinetic impact associated with fluid composition and movement. Balancing degrees of protection, usually to increase the useful life of the device, with sensor response and accuracy is a frequent challenge in the process measurement and control field. Industrial processes commonly are associated with corrosive or toxic fluids, often at extreme pressure or temperature and containing various levels of solids. Any of these traits can pose substantial risk to process performance and uptime. Operations that process fluids will employ pressure measurement devices to monitor process performance and maintain system safety levels. There are many instances where characteristics of the process and its media are not compatible with pressure measurement devices. Here are some potentially problematic scenarios for pressure measurement instruments: Corrosive media that will prematurely deteriorate the pressure sensing element. Viscous or fibrous media, also those that may crystallize or polymerize, posing a risk of clogging channels, tubes, and orifices of pressure measurement devices. Media temperature that is beyond the rated range for the pressure measurement device has a potential to damage the instrument or cause error in the pressure reading. A measuring point that is remotely located from where a technician may need to observe the reading. Also conceivable, the pressure measurement device needs to be located away from other potentially damaging environmental conditions. The process requirements dictate specific hygienic requirements that are cause for the measurement device to be isolated from the medium. Toxic or otherwise hazardous media that must be contained. Excursions of system pressure may exceed the acceptable range of the instrument, potentially damaging the device. A solution which can provide protection from the items listed above, while still maintaining instrument response and accuracy is a diaphragm seal. Seals are placed between the pressure measurement device and the process media. The space between the diaphragm, which is flexible, and the sensor is filled with a fluid that will hydraulically transfer the pressure condition on the process side of the diaphragm to the sensor. The diaphragm serves as a physical barrier between the potentially damaging media and the instrument. Diaphragm seals are available in a wide variety of configurations to accommodate any media type or connection requirement. Seal selection involves specifying the connections and form factor to properly mate the diaphragm with the instrument and the process, then selecting the diaphragm material that will be compatible with the media. The best way to achieve a positive solution is to share your requirements with a qualified assembler. They can help select the right diaphragm seal and mate it up with a pressure gauge, providing a complete assembly that is ready to be installed in your process.
What is the meaning of the phrase quantitively transfer the precipitate to the filter paper?
To quantitatively transfer something means to transfer every particle of the material. This is opposed to qualitatively transferring which requires just enough to examine.
What is the transfer of thermal energy between two bodies which are at different temperatures?
Thermal energy can be transferred by conduction, convection, or radiation. The formulae for the rate of transfer - if that's what you are after - vary, depending on which type of transfer is predominant.
What has the author K J Wilcock written?
K J. Wilcock has written: 'Viscosity and heat transfer in gas fluidised beds'
How does temperature affect viscosity and density?
Viscosity: In gasses, forces between atoms are not important and the transfer of momentum (hence force, hence viscosity) between different adjacent regions of a fluid is due to the movement of particles over long distance. Higher temperature means faster movement means higher viscosity in a gas. In liquids, forces between particles dominate and shear force is transmitted through those interactions with adjacent particles. Higher temperature means more short distance particle movement and more varied interaction with neighboring particles thus decreasing the effectiveness of transmitting shear force and decreasing viscosity. (These trends in viscosity are only general and complex interactions of particles can produce different results than described here.) Density: If the pressure is held constant, an increase in temperature normally results in an increase in volume of a liquid, solid or gas. This parallels the explanation of how particle motion at the microscopic level produces pressure by collisions with the walls of the containing volume. More temperature means more energetic particles that have more momentum to transfer to container walls. With constant pressure, the walls expand. (The obvious caveat here is that molecular orientations and molecular forces can be complex and this connection between increased temperature and decrease density is not universally true. The properties of water between 0 Celsius and 4 Celsius are a well known counter example to the general rule.)
Why is oil difficult to transfer from one container to another?
Oil is difficult to transfer from one container to another because of its high viscosity. Pouring oil from one container to another is a slow process and time consuming.
The formation of waves is a result of what?
Momentum transfer or pressure variances.
What type of oil goes in an 1999 Isuzu Rodeo transfer case?
The recommended transfer case fluid is a SJ-rated 5W30 viscosity oil. One example would be Amsoil 5W30 Synchromesh Fluid. The vehicle requires approximately 1.35 quarts of transfer case fluid.
Where you will use the transfer pump and the booster pump?
transfer pupm is use in that area where systems need more pressure(low to high) and booster pump is use in that area where system need low pressure.
Which SI unit is named for scientist whose principle describe transfer of pressure in an enclosed fluid?
The SI unit that is named for the scientist whose principle described transfer of pressure in an enclosed fluid is pascal.
Which Si unit is named for the scientists whose principle describes transfer for pressure in an enclosed fluid?
The SI unit that is named for the scientist whose principle described transfer of pressure in an enclosed fluid is pascal.
Which si unit is named the scientist whose principle described transfer of pressure in an enclosed fluid?
The SI unit that is named for the scientist whose principle described transfer of pressure in an enclosed fluid is pascal.
What are the differences between simple calorimeter and bomb calorimeter?
bomb calorimeter measures heat transfer at constant while the cup measures at constant pressure.
How do you use a cane?
you put the cane in your hand and lean on it as you walk. When you have trouble putting pressure on your feet you transfer the pressure to the cane.
What SI unit is named for the scientist whose principle described transfer of pressure in an enclosed fluid?
Blaise Pascal first described the transfer of pressure in an enclosed fluid in Pascal's law. The SI unit for pressure, stress, and tensile strength was made the Pascal in his honor.
