0
There is some equipment that will operate on 208 volts even though it is rated to be use 240 volts.
See discuss question below.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Which leg is 208 on 3 phase power?
On three phase 208 volts one leg does not have the potential of 208 volts. It takes two legs to provide the 208 volts. The potential is across AB, BC and CA. Voltage to the grounded neutral A-N, B-N and C-N will produce a potential of 120 volts. In a wye configured secondary three phase four wire you have the potential of 120/208 volts.
What if the input power is 208 volts line to line two phase 8 amps to a heating element vs 110 volts 8 amps to a heating element How is watts calculated?
To calculate watts, you need to multiply the voltage (in volts) by the current (in amps). For the 208 volts, 8 amps heating element: Watts = 208 volts * 8 amps = 1664 watts For the 110 volts, 8 amps heating element: Watts = 110 volts * 8 amps = 880 watts
What is the kilowatt output of an electric heater that has an ampere draw of 50 a and a voltage source of 208 volts?
The watts is the volts times the amps So 208 x 50 watts, or 10.4 kW.
What is the maximum volts that can be used on a 208 230 volt motor?
You should not go above 240 volts for that type of motor.
How do you covert 120 volts to 208 volts?
Single phase or three phase? 120/208 would be measured hot to ground for 120 and hot to hot (phase to phase) for the 208 reading. Any hot to ground will read 120 and any two phases together will read 208.
How do you meter a 208v load meter only 1 phase add the two?
The voltage 208 is a three phase voltage. Single phase is classed as the voltage obtained from any two legs of the three phase voltage system. The voltage between L1 to L2 = 208. L2 to L3 = 208 volts and L3 to L1 = 208 volts. To measure the load of the 208 volt device just clamp an amp meter around one of the legs coming from the load. This will give you the amperage that the load draws.
Does a 208 volt outlet need a neutral?
No a 208 volt outlet does not need a neutral. 208 volts is the line voltage between any two legs of a three phase 208 volt system.
Can you operate a 208 volt on 110 volt?
The United States is one of the only places in the world that uses 110 volts instead 220 volts. In order to operate 208 volts on a 110 volt electrical current, you will need a voltage converter.
How do you read 208 volts single phace circuit?
All voltage reading are usually read with a volt meter. This volt meter can be a hand held unit like electricians use.
Which leg is 208 on 3 phase power?
On three phase 208 volts one leg does not have the potential of 208 volts. It takes two legs to provide the 208 volts. The potential is across AB, BC and CA. Voltage to the grounded neutral A-N, B-N and C-N will produce a potential of 120 volts. In a wye configured secondary three phase four wire you have the potential of 120/208 volts.
What if the input power is 208 volts line to line two phase 8 amps to a heating element vs 110 volts 8 amps to a heating element How is watts calculated?
To calculate watts, you need to multiply the voltage (in volts) by the current (in amps). For the 208 volts, 8 amps heating element: Watts = 208 volts * 8 amps = 1664 watts For the 110 volts, 8 amps heating element: Watts = 110 volts * 8 amps = 880 watts
How do you convert 230v to 208 volts single phase?
A source of 208 volts can be obtained from any two legs of a three phase four wire 208 volt system. The two legs are classed as single phase 208 volts. The lead tags can be L1-L2, L2-L3, or L3-L1 all of which will give you 208 volts. Any of these lead tags to the grounded star point (wye) will give you 120 volts.
How will a 3 phase panel give you 110 volts and 220 volts?
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
How does 120 volts come from 208 volts?
208 is a three phase wye connection voltage. To obtain the each individual coil voltage the 208 is divided by 1.73 which equals to 120 volts. Hence you have 3 phase 208 voltage on the phase legs and 120 volts to the wye point which is grounded. This same formula is used on any 3 phase system. 600/347, 480/277, 208/120.
What is the kilowatt output of an electric heater that has an ampere draw of 50 a and a voltage source of 208 volts?
The watts is the volts times the amps So 208 x 50 watts, or 10.4 kW.
What is the maximum volts that can be used on a 208 230 volt motor?
You should not go above 240 volts for that type of motor.
What is the standard voltage?
In the USA it is usually 120/208 or 120/240 volts In Europe I think it's 220 volts
