0
You can, but you will destroy the lugs certification if you do. Without the certification on a field modified piece of equipment you stand the chance of getting a rejection if the project is ever inspected by an electrical inspector.
Just use the double barrel lug until you can get a proper single barrel lug and then change it out. Keep in mind the cost of a double barrel lug is about four times that of a single barrelled lug.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What is the hole size required for a 2.5 conduit?
A trade size hole for a 2-1/2" EMT conduit connector, the hole needs to be 2-7/8" in diameter. A 3" rigid conduit can also use this size hole without the lock nuts falling into the hole.
How many wires can be pulled through a 1 inch hole?
The answer will differ depending on the size of the wires that are to be pulled through a one inch (25mm) hole. How many 12/2 wires can be pulled through a 1" hole. I will also use some 14/2 and 12/3 .
What is the cut off mark in lpsc valiamala for technical assistant in diploma electronics eng?
1/3 may be
What size hole should be drilled for wire that will be pulled through the walls?
3/4 in hole good, 1 in hole better. That gets you a full 1 and a half inches from nails and dry wall screws etc and allows electricians to come back and pull more wire etc. Depending on circumstance you may also want to put steel plates over the 2x4 where you drilled the hole, so if some idiot comes behind you with trim nails longer than 2 inches you wont get a short or set the house on fire also a good idea where plumbers drill for pipes... Irecommend a short auger bit to drill with and angle headed Drill. Milwaukee makes an excellent one. I work as a remodel carpenter and am a journeyman electrician.
How do you wire breaker box to earth ground rod?
ITS NOT TO COMPLICATED REALY, YOU NEED A HOLE BIG ENOUGH FOR GROUND WIRE GOING OUT TO PASS THROUGH THE BOX, IF IT IS FOR A BREAKER PANEL IT SHOULD HAVE AN ADAPTER THAT HAS THE INSERT THROUGH THE BOX WITH A LOCKING NUT AND A BUSHING ( PLASTIC ) THAT KEEPS THE CABLE FROM GETTING DAMAGED FROM COMING IN CONTACT WITH METAL BOX. THERE SHOULB BE A GROUNDING BUSS IN THE BOTTOM OR ONE OF THE SIDES THAT HAS THE ATTACHMENTS FOR THE GROUNDS FROM 1 TO WHO NOWS HOW MANY DEPENDING ON HOW MANY GROUNDS YOU WILL NEED.( ONE BIGGER GROUND WIRE COMING IN TO BUSS BAR, SEVERAL( DEPENDING) SMALLER WIRES COMING FORM THE FEEDS THROUGHOUT THE STRUCTURE. )ONCE YOU GET BUSS AND INCOMING GROUNDS, THE ONE THAT ATTACHES TO THE GROUND ROD AND THE WIRE ( BE SURE TO PUT THE ACCORN CLAMP ON BEFORE YOU PUT THE GROUND ROD INTO THE GROUND , IN CASE IT GETS MUSHROOMED DOWN FROM DRIVING IT INTO THE GROUND) USE WATER IN THE HOLE , RAISE THE GD. ROD UP AND DOWN KEEPING THE HOLE FAIRLY WET . IF IT IS JUST DIRT IT WILL GO IN REAL EASY, IF THERE IS ROCKS AND ETC. IN HOLE YOU WILL HAVE TO DRIVE IT IN. THE FURTHER GROUND ROD GOES IN THE BETTER. 10 FEET IS THE COMMON LENGTH FOR THE ROD TO GO INTO THE DIRT .ATTACH THE WIRE TO THE ROD WITH THE CLAMP YOU PUT ON PRIOR TOO AND YOU HAVE GOT IT.
Do 5 lug universal rims fit 6 lug vehicles?
No they will not.They are 1 bolt hole less then 6.
What direction do fluids flow when there is a hole in the container?
Fluids flow down or down and outward, depending on the location of the hole--or path of least resistance. Fluid will stop flowing toward a hole once the fluid level is lower than the hole. So if you marked a line 1/4th inch down from the top of a styrofoam cup, cut a hole at that line (put your finger over it temporarily), and add water to the top and remove your finger, the water will flow sideways and down until the water is below the cut hole. If you poked a hole 1/4th inch up from the bottom, the water would continue to drain to below the second cut hole.
What is clevis?
A Lug is a flat end of a bar that is rounded on the edge and has a hole for attaching something with a bolt. A Clevisis an extension of a part that has a pair of Lugs that uses 1 bolt that fits through a hole in each lug.
What is a clevis?
A Lug is a flat end of a bar that is rounded on the edge and has a hole for attaching something with a bolt. A Clevisis an extension of a part that has a pair of Lugs that uses 1 bolt that fits through a hole in each lug.
How do you get a shappfire in Pokemon LeafGreen?
You get it in the dotted hole in ruin valley and use cut on the door and fall in the first hole and fall in the rest in this order 1. up 2. left 3. right and 4. down
How long does it take to cut down 1 tree?
1 tree is cut down every 7 seconds
What are the release dates for Classic Alice - 2014 Down the Rabbit Hole 1-1?
Classic Alice - 2014 Down the Rabbit Hole 1-1 was released on: USA: 2014
What happens to the volume of the air when you cut down trees?
If you cut down about 10 the volume goes down 5 if you cut 9 its 4 if you cut 8 its 3 if you cut 7 its 2 if you cut 6 its 1 But if you cut 5 or LESS No volume goes down!
Where is the pusle on 7 island in Pokemon LeafGreen?
1.USE CUT ON The door. 2.Enter 3.Jump in the hole 4. Go to the top hole 5. go to the left hole 6. go to the right hole 7.go to the down hole 8. Approach the sapphire(blue stone) and press a. 9. go to island 5 to the rocket ware house HOPE I helped
What are the release dates for Aidan 5 - 2009 Down the Rabbit Hole Part 1 1-8?
Aidan 5 - 2009 Down the Rabbit Hole Part 1 1-8 was released on: USA: 27 May 2011
What are the release dates for Once Upon a Time in Wonderland - 2013 Down the Rabbit Hole 1-1?
Once Upon a Time in Wonderland - 2013 Down the Rabbit Hole 1-1 was released on: USA: 10 October 2013
What are the ratings and certificates for Once Upon a Time in Wonderland - 2013 Down the Rabbit Hole 1-1?
Once Upon a Time in Wonderland - 2013 Down the Rabbit Hole 1-1 is rated/received certificates of: USA:TV-PG
