0
Yes.
Additional InformationBreakers and fuses protect the wires to prevent fire. The 100 Amp breaker in the meter base (main) protects the wire from the meter base to the breaker panel. The 50 Amp breaker in the breaker panel protects the wire from the breaker panel to the outlet. Sometimes the 100 amp main breaker is located in the panel.
If you are asking "Can you use two 50 amp breakers for the main breakers with a 100 amp service, then yes you can. The National Electrical Code allows you to use up to 6 breakers as the main overcurrent protection.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How many 50 amp outlets can you run off a 125 amp main panel?
It depends on duty factor of each connected device. For a continuous load you can support 80% of 125 Amps which is 100 Amps. That would support two 50 A breakers each supporting a 40 Amp continuous load. If your loads were less and not continuous you can have more breakers. It is all a matter of supply and demand.
How many 50 amp breakers feeding 50 amp outlets can you install from a 125 amp main panel?
Three or four would be normal. The total current should not exceed the rating of the main panel, so depending on how intensively the different circuits are used, more could be installed.
How many breakers can be put in a 50 Amp subpanel?
As many as you need. Just make sure the main breaker of the subpanel stays below 50 amps (the rating of the subpanel) and the input to the subpanel, whichever is lower.
Can you had a 20 amp breaker on your 70 amp sub-panel that has already 70 amp total on it that consist of one 50 and two 15 amp breakers and the panel has 4 available spaces out of 8?
SeeIf_a_100A_breaker_panel_has_five_15A_breakers_and_four_20A_breakers_could_this_overload_the_panel
How do you power a 50 amp kiln in your garage?
By supplying it with a 50 amp feed from your main distribution panel.
Is it OK to have 250 A of breakers in a 100 A panel?
Yes. Many installations have breaker totals higher that the main breaker of the panel. It is worked on a percentage basis. Not all of the breakers will be on at the same time. In a home, on a 100 amp panel the average load is 50 - 60 amps. The 100 amp main breaker is protecting the 100 amp rated panel board. If the load current goes higher that the panel board is rated at, the main breaker will trip to protect the board.
How many 50 amp outlets can you run off a 125 amp main panel?
It depends on duty factor of each connected device. For a continuous load you can support 80% of 125 Amps which is 100 Amps. That would support two 50 A breakers each supporting a 40 Amp continuous load. If your loads were less and not continuous you can have more breakers. It is all a matter of supply and demand.
How many 50 amp breakers feeding 50 amp outlets can you install from a 125 amp main panel?
Three or four would be normal. The total current should not exceed the rating of the main panel, so depending on how intensively the different circuits are used, more could be installed.
How many breakers can be put in a 50 Amp subpanel?
As many as you need. Just make sure the main breaker of the subpanel stays below 50 amps (the rating of the subpanel) and the input to the subpanel, whichever is lower.
How are quad circuit breakers used?
This would typically be seen in older residential installations where the service was of such a high amperage that the mains required larger breakers than were available (for that panel). Placing two breakers in parallel allowing sharing of the load. Two breakers per (split) phase would total four breakers. Two breakers of 50 amp rating each (in parallel) provide (generally) 100 amps of protection. Two sets of two would provide mains protection for a 200 amp service.
Why does the main circuit breaker trip but not the smaller branch circuit breakers?
If the main breaker has ground fault detection, and the fault is a ground fault, then only the main may trip. Also if the fault is a direct short, the fault current may be several thousand amps, much greater than the trip point of both breakers. Breakers have an I^2T curve (current squared-time), which is an indication of how fast the breaker will trip at a given overload. When both breakers are overloaded, the breaker with the faster I^2T rating at that current level will trip first. This would be an indication that the breakers are improperly specified or adjusted.
Can you had a 20 amp breaker on your 70 amp sub-panel that has already 70 amp total on it that consist of one 50 and two 15 amp breakers and the panel has 4 available spaces out of 8?
SeeIf_a_100A_breaker_panel_has_five_15A_breakers_and_four_20A_breakers_could_this_overload_the_panel
How do you power a 50 amp kiln in your garage?
By supplying it with a 50 amp feed from your main distribution panel.
Why are there two 15 amp breakers connected to your 30 amp breaker?
Answer for UK, Europe and countries running a 50 Hz supply service.It is acceptable to connect two 15-amp breakers to a 30-amp supply. It woud also be acceptable in some applications to connect three 15-amp breakers if it were known that the total current would not exceed 30 amps. For example in many UK properties there is a 60-amp supply, and connected to this there are two 30-amp supplies for the ring-circuit and the cooker, plus also a 10-amp lighting supply.
Need to move 2 breakers to a sharing breaker to add a 50 amp breaker need info on how to do this?
by doing your mum
Why does my heating and air conditioner in my house have 3 double pole breakers - a 30 40 and 50?
In North America a two pole breaker usually represents a load that requires a 240 volt source. Larger current load appliances use 240 volts to reduce the feeder size and there by reduces the cost factor when wiring a building. Two pole 15 amp breakers are used for kitchen counter split receptacles.Two pole 20 amp breakers can be used for baseboard heating and hot water tanks.Two pole 30 amp breakers can be used for clothes dryers and some heating units.Two pole 40 amp breakers can be used for electric ranges.Two pole 50 amp breakers are not common in home wiring circuits. It might be used for an electric furnace or some other high current device.
Can you use a 200 amp subpanel on a 100 amp branch circuit?
Yes you can, but it is all about distribution of the load. You still have a maximum limiting current of 150 Amps. So if you did use 100 amps on the sub-panel that would only leave 50 amps on the main. Since power usage is usually not constant and varies by day and situation, you just need to make sure the load is distributed so you don't start tripping breakers.
