0
It depends on duty factor of each connected device. For a continuous load you can support 80% of 125 Amps which is 100 Amps. That would support two 50 A breakers each supporting a 40 Amp continuous load. If your loads were less and not continuous you can have more breakers. It is all a matter of supply and demand.
What else can I help you with?
How many 50 amp breakers feeding 50 amp outlets can you install from a 125 amp main panel?
You can install a maximum of two 50 amp breakers feeding 50 amp outlets from a 125 amp main panel. Each 50 amp breaker is using half of the available amperage from the main panel.
Should a 2 AWG copper wire be used to feed a 125 amp sub panel located 125 feet from main panel?
No, the conductor is too small. The feeder to a 120/240 volt sub panel should be a 1/0 copper or a 2/0 aluminium conductor. This size conductor will limit the voltage drop to 3% or less when supplying 125 amps for 125 feet on a 240 volt system. ACWU 90 (Armoured Cable Wet location Underground 90 degree C). ACWU 90 cable is code approved for direct burial and is used in many projects as an underground service distribution feeder. Aluminium is much cheaper than copper for this type of installation.
How can you find out the bus bar rating in a panel that is old and the rating sticker has fallen off is it safe to say that a panel with a 100 amp main breaker has a bus rated AT 125 AMPS?
A 100 amp panel should have a conservatively rated busbar and wiring but this says nothing about your particular panel. If you are asking a question relating to safety it needs to be seen by an electrician.
Can you hook up 200 amp dervice to a 125 amp service panel?
No, it is not safe or recommended to connect a 200 amp service to a 125 amp panel. The panel must be rated to match the amperage of the service to avoid overloading the panel and potential fire hazards. It is important to upgrade the panel to match the service amperage.
Where is the neutral bus bar in a stab-lok panel BE116-32 125 amp.?
The neutral bus bar in a Stab-Lok panel BE116-32 125 amp is typically located on the side or at the bottom of the panel box. It is a metal bar with multiple screw terminals for connecting the neutral wires from branch circuits. Refer to the panel's installation manual or contact a qualified electrician for specific guidance on locating and working with the neutral bus bar.
How many 50 amp breakers feeding 50 amp outlets can you install from a 125 amp main panel?
You can install a maximum of two 50 amp breakers feeding 50 amp outlets from a 125 amp main panel. Each 50 amp breaker is using half of the available amperage from the main panel.
What is the maximum amperage capacity of a 125 amp panel with main breaker?
The maximum amperage capacity of a 125 amp panel with a main breaker is 125 amps.
What is the maximum amperage capacity of the 125 amp main breaker in this electrical panel?
The maximum amperage capacity of the 125 amp main breaker in the electrical panel is 125 amps.
What is the recommended size for the main breaker in a residential electrical panel, specifically for a 125 amp main breaker?
The recommended size for a main breaker in a residential electrical panel with a 125 amp main breaker is typically 150 amps.
What are the key features and specifications of the Siemens 125 amp panel?
The Siemens 125 amp panel is a electrical distribution panel that can handle up to 125 amps of electricity. It typically has a main breaker or main lug, multiple circuit breakers for individual circuits, and is designed for residential or light commercial use. It is important to consult the specific model's specifications for exact details on features and dimensions.
What are the key features and specifications of the Square D 125 amp panel?
The Square D 125 amp panel is a type of electrical panel that can handle up to 125 amps of electricity. It typically has a main breaker or main lug, along with multiple circuit breaker slots for individual circuits. The panel is designed to safely distribute electricity throughout a building, with features such as overload protection and grounding capabilities. It is important to consult the manufacturer's specifications for specific details on the panel's dimensions, materials, and installation requirements.
What is the recommended wiring diagram for a 125 amp sub panel installation?
The recommended wiring diagram for a 125 amp sub panel installation typically involves using a 2-pole breaker in the main panel, running 4 wires (2 hot, 1 neutral, 1 ground) from the main panel to the sub panel, and connecting them to the corresponding terminals in the sub panel. It is important to follow local electrical codes and consult a professional electrician for proper installation.
What is the function of the Square D 125 amp main breaker in an electrical panel?
The Square D 125 amp main breaker in an electrical panel serves as a safety device that controls the flow of electricity into the panel. It is designed to trip and disconnect power in case of an overload or short circuit, protecting the electrical system from damage and preventing potential hazards such as fires.
How many amps can be put on a 125 amp service?
You should not load a 125 amp panel any more than 100 amps.
What are the key considerations when selecting a 125 amp main breaker panel for a residential electrical system?
When selecting a 125 amp main breaker panel for a residential electrical system, key considerations include ensuring it is compatible with the electrical service size, has enough circuit spaces for current and future needs, is of good quality and safety standards, and meets local building codes and regulations.
What wire size do you need for a 125 amp panel with a 100 amp main breaker?
A #3 copper conductor with an insulation factor of 90 degrees C is rated at 115 amps. Even though the panel is rated at a higher amperage it is the main breaker that governs the wire size.
What is the compatibility of a Square D 125 amp breaker with my electrical panel?
To determine the compatibility of a Square D 125 amp breaker with your electrical panel, you need to check the manufacturer's specifications for your panel to see if it is rated to handle a 125 amp breaker. It is important to ensure that the breaker is compatible with the panel to avoid any safety hazards or damage to the electrical system.
