answersLogoWhite

0


Best Answer

It can be done but it requires knowledge about how a 3way is wired to convert it to a regular switch. It would involve testing live wires to determine where power starts at. You can't just replace one switch.

User Avatar

Wiki User

โˆ™ 2005-04-02 06:01:03
This answer is:
User Avatar
Study guides

Physics

20 cards

What type of circuit in which all parts are connected in a single loop

What angle is between 90 and 180

What condition has symptoms that include ringing buzzing or roaring in the ears or head

What is the transfer of energy as electromagnetic waves called

โžก๏ธ
See all cards
4.1
โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…
10 Reviews

Add your answer:

Earn +20 pts
Q: Can you replace a 3-way light switch with a standard switch and cap off the wires or can you use the 3-way switch and make it into a standard switch?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Can you replace a 3 way light switch with a standard switch and cap off the wires or can you use the 3 way switch and make it into a standard switch?

YES


What causes arcing and a scratching noise when you turn off a light switch?

An old/worn/faulty light switch, or the wires connected to the switch are loose. Replace the switch ASAP.


How do you replace brake light switch on suzuki forenza?

To replace the brake light switch on a Suzuki Forenza, locate it on the pedal shaft, release the wires that connect it, twist and then take out the old brake light switch and put a new switch in its place. The job can be done by any handy owner.


How do you replace pressure switch on jacuzzi spa?

To replace the pressure switch on a Jacuzzi spa you need to disconnect the wires from the thermostat to the pressure switch. Remove the pressure switch, replace with new one, and reattach the thermostat wires.


What 6 things do you need to make a torch?

to make a torch you need batteries (obviously), a switch (you can buy a standard switch or make a pressure switch out of foil and cardboard), a light bulb, wires (3 if you are using any kind of switch) and a housing (something to hold the batteries, wires, light bulb etc. together). I would also recommend using a light bulb holder and wires with alligator clips (if you dont have solder) as these make the construction more sturdy. they may increase bulk but they are worth it especially as it is easy to replace the bulb and there is no solder needed therefore nothing has to be broken to replace anything.


How do you replace the brake light switch on a 1996 suburban?

Look under the dash on the 1996 suburban, and locate the brake light switch on the brake pedal arm. Remove the switch nut, and slide the switch out. Unplug the wires from the switch and install the new switch.


How do you get your car windows to roll up when the switch for automatic windows is broken for a 1995 Isuzu Rodeo?

Replace switch or "jump wires" on switch to operate windows Replace switch or "jump wires" on switch to operate windows


Why does the light switch crackel when turned off?

Either there is a loose connection where the wires are attached to the switch, or there is a bad connection inside the switch itself. Turn the breaker off that controls that switch. Remove the cover plate. make sure the wires are tightly connected. If they are tight, replace switch.


Is a light switch a conductor?

No, a light switch is a device it does conduct electricity when closed but it is not a conductor. Wires are conductors.


How do you install a Hazard light swithch in a 2000 Malibu?

remove trim plate around switch,take out screws holding switch in,remove wires then replace in reverse order!!


How do you change backup light switch on a BMW?

Backup light switches are different between automatic and manual transmission bmws. If you have the automatic the switch is under the shifter. Disconnect the battery and remove the shifter boot. Unplug the switch wires and replace the switch and reconnect the wires and battery. If you have a manual transmission the switch is on the passenger side of the transmission above the Allen type filler plug. Disconnect the battery, unplug the wires and unscrew the switch with a 19mm wrench. Screw in the new one an torque it down then reconnect the wires and the battery.


How does light turn on and off with no switch and light and no wires?

Perhaps by unscrewing the bulb light.

People also asked