0
Can you supply three 220 -240 volt 16.6 amp infrared heaters with one circuit?
Wiki User
∙ 9y ago
Can you supply three 220 -240 volt 16.6 amp infrared heaters with one circuit?
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What is a y configuration on a 3 phase circuit?
On a wye connection all three ends of the phase winding coils are connected together and grounded. The other end of the three phase winding are connected to the supply voltage.
Is line to line fault a 3 phase fault?
'Line conductors' are the three 'hot' conductors (A-B-C) that connect a three-phase supply to a three-phase load. In some cases, a pair of line conductors (e.g. A-B, B-C, or C-A) is used to supply a single-phase load. A 'line fault' can be a short-circuit fault between all three, or any two, of these line conductors -whether they supply a three-phase load or a single-phase load.
When a circuit is described as a three-phase delta-connected 240 v circuit its categorized by?
circuit characteristics.
What are the disadvantages of a series circuit?
Series circuits like a string of Christmas lights, can be very annoying. If one bulb in burnt out, broken, or unproperly screwed, the entirely will disconnect and the system will fail. Cheack out clara-the-awesomest.tumblr.com
How do you calculate the joint resistance in a series circuit with three resistances?
The resistance of a series circuit is simply the sum of the individual resistors.
What would be the result of three defrost heaters each 12.5 ohms wired in series to a 115 volt power supply if the heaters were to supply a 360 watt heating load?
But why do you want to connect them in series since this will under feed the heaters? I recommend that you connect them in parallel across the supply so that they each have 115v and thus provide good heating effect.
What circuit you can use to run three phase motor?
It must be a three phase supply service to run a three phase motor.
How do you calculate total energy for a circuit that has three capacitors(10µF 15µF and 30µf) and a 20v dc supply?
Energy = (Capacitance*(Voltage)^2)/2. Three capacitors are there. Are they in series or in parallel. It is not mentioned. So friend has given only the formula as guidelines.
On an 50A circuit should you be able to turn all of three of your electric heaters on at the same time without tripping the main breaker?
Check the amp rating of the heater and do the math. Electric heaters pull A LOT of current, so I'm guessing you'd be near the 50amp max.
What are the three requirement for a complete circuit?
-- a power supply -- a load -- low-resistance material to connect the load to the power supply
What would be the voltage suplied to each circuit if three circuits are connected in parallel with a power supply of 30 volts?
30 volts.
Why you use three phase supply in experiment of power factor of RL series circuit?
You don't necessarily. For a straightforward series (or parallel) R-L load, you will only require a single-phase supply. However, if you had three R-L loads, connected in delta or star (wye), then you would require a three-phase supply.
What radiations does the sun give out?
The sun emits Ultraviolet, Visible Light and Infrared Radiation, with wavelengths ranging from 100nm to 1mm. Ultraviolet Radiation is split up into three ranges: UVA, UVB and UVC rays. Infrared is also split into three ranges: Infrared-A, Infrared-B and Infrared-C.
How does work ic-7805 in infrared object counter?
The 7805 is a three terminal 5 volt regulated power supply. You provide a ground, a DC supply somewhat higher than 7 volts, and it provides a regulated 5 volts output.
Can you connect two hot water heaters together?
Yes, domestic hot-water heaters are often connected in parallel for added volume of hot water or in series for more efficient heating of the water. In a commercial installation there could be three or more heaters in parallel for increased simultaneous volume and another in series to supply the others for pre-heating to speed recovery to a comfortable temperature.
What does ground do on a three prong plug receptacle?
The ground blade on a three blade plug (cap) is to provide a low impedance return to the voltage source. If the portable equipment develops a short in its circuit and goes to ground, it is this blade that will carry the short circuit current back to the supply distribution panel and trip the breaker open to cut off the supply voltage.
Why Scott connection is used to convert three phase to two phase why cant you take two lines from three phase circuit?
In a two-phase connection, the phases are displaced by 90 degrees. Two lines (not 'phases') of a three-phase system will provide a single-phase supply, not a two-phase supply.
