Yes, if there is a 208 volt connection on the multi tap ballast. One side of the 208 to the common terminal and the other side of the 208 supply to the 208 volt lead. <><><> As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
No, the ballast is designed to be only used with a 120 volt input.
If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.
Yes, but it will not work.
Yes, you can easily use it. Just install it as you would any other 120 volt light fixture and change the bulb from a 240 volt bulb to a 120 volt bulb. It will work just fine.
Operating at half the required voltage, the lamp will not operate at full capacity if it comes on at all.
The timer has to be multi-pole. The ballast must be connected to the load contacts of the timer. If the timer is a 120 Volt timer, the timer has to run on a 120V. circuit. Loads are loads, and as long as you have a multi-load timer you can hook up whatever you want. If the timer only works on a shared power source (load shares the timer supply) you will need to use a contactor on the load side or the timer.
need a universal voltage ballast 120/277 volt or a 277volt ballast
If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.
No, not a good idea. You have to use a 347 volt ballast.
Yes, but it will not work.
You don't. A ballast with a 347 volt input is a commercial ballast. The 347 volts comes from a 600 volt three phase four wire Y system. You can change the ballast out to a 120 volt and rewire the unit but in most cases it is cheaper to buy a completely new lighting fixture.
Is it incandescent or flourescent? If it's incandescent it will work okay--it'll be dim but it will work. A fluorescent probably wouldn't fire. Now having said that, if this is a European lamp google "110v European base bulbs" and you'll find light bulbs that work on 110v but have bases that screw into European sockets. Just change the plug on the lamp and you're golden.
NO! a 120-277 electronic ballast requires one "hot" wire and a neutral from either a 110V or 277V supply. If you supply it with two "hot" wires from a 208 V supply, it will instantly burn up.Yes. A ballast with a specification range of 120 volt to 277 volt will work on 208 volt. These ballast use intelligent voltage sensing technology and it does not matter if the source is a hot and neutral or two (2) hots. Don't believe it? Call a ballast manufacturer instead of giving incorrect answers.
If you want your bulbs to last longer then use 130 volt bulb on a 120 volt system. The light emitted by a 130 volt bulb, when comparing it to a 120 volt bulb, will be a bit dimmer.
Yes a 220 volt light bulb will run on a 120 volt circuit but at 1/4 of the wattage that the light bulb is rated at. A 100 watt light bulb on 220 would would be equal to a 25 watt light bult on 120 volt system.
It sounds like you are talking about a two tube eight foot fluorescent fixture. Open the fixture up and you will find a ballast that has probably two yellow wires, two blue wires, two red wires and a black and white wire coming out of it. The 120 volt supply will connect to the black and white wires that protrude out of the ballast. Black ballast to black supply and white ballast to white supply.
Not unless you have 277 volts in your garage. Open the fixture and check the ballast. Some of the commercial fixtures have multi tap connections for different voltages. If 120 or 240 volt tap is present then you can use the fixture.
you don't. you just take and use 120 volts from the 220. At least that's what I'd do.