0
Can you tell the difference between a 15 or 20 amp circuit by the receptacle my box has 10 amps on the breakers and I know there is no such thing?
LynneGrahamWashingto...
!0 amp breakers have not been used for quite some time . NEC made 15 amp the minimum requirement for 110/120 VAC circuit breakers a long time ago. If the breakers are only 10 amp, then those outlets can only carry 10 amps max.
I would call an electrician. Your electrical service is terribly out of date and, in my opinion, inadequate and unsafe.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Are Ground fault circuit interrupter GFCI devices available for use on 240 volt 480 volt and 600 volt circuits?
Yes, in the form of GFCI circuit breakers, not as a receptacle.
The purpose of the SEC's circuit breakers rule is to?
The purpose of the SEC's circuit breakers rule is to:
Is a circuit breaker an alternative fuses?
Circuit breakers do the same thing as fuses. They interrupt current flow when a certain preset point is reached. The difference between circuit breakers and fuses are that circuit breakers are resettable and reusable, whereas fuses are one time devices that must be replaced after they blow.
What breakers are compatible with ge breaker boxes?
GE circuit breakers with catalog numbers ranging from THQL1115 through to THQL1150 can be substituted like for like with Cutler-Hammer circuit breakers coded CL115 through to CL150, ITE Siemens circuit breakers coded Q115 through to Q150 and Square D circuit breakers coded HOM115 through to HOM150. These are single pole breakers. GE circuit breakers with catalog codes from THQL2115 through to THQL2150 can be substituted with Cutler-Hammer circuit breakers CL215 through to CL250, Square D circuit breakers HOM215 through to HOM250 and ITE Siemens circuit breakers Q215 through to Q250 of the same amperage and voltage. These are double pole breakers.
What breaker boxes are compatible with GE circuit breakers?
GE circuit breakers with catalog numbers ranging from THQL1115 through to THQL1150 can be substituted like for like with Cutler-Hammer circuit breakers coded CL115 through to CL150, ITE Siemens circuit breakers coded Q115 through to Q150 and Square D circuit breakers coded HOM115 through to HOM150. These are single pole breakers. GE circuit breakers with catalog codes from THQL2115 through to THQL2150 can be substituted with Cutler-Hammer circuit breakers CL215 through to CL250, Square D circuit breakers HOM215 through to HOM250 and ITE Siemens circuit breakers Q215 through to Q250 of the same amperage and voltage. These are double pole breakers.
How can all breakers be live and outlets not work?
The very first outlet in the circuit has a break, probably where the wires enter the receptacle.
Are Ground fault circuit interrupter GFCI devices available for use on 240 volt 480 volt and 600 volt circuits?
Yes, in the form of GFCI circuit breakers, not as a receptacle.
Why do two circuit breakers control the same circuit 120 volts on all devices in circuit?
Circuit breakers are like fuses that you can reset. There is no need for two though because they do the same job as one, which is to open the circuit as soon as the voltage that is being called for by all the devices becomes greater than the 120v you mentioned. <<>> It sounds to me like you are talking about a three wire split receptacle On kitchen counter plugs and sometimes other locations the electrical code requires that split receptacles be installed. This request came about by people trying to plug too many appliances into one 15 amp circuit. The circuit not being able to carry the load and constantly tripping the breaker. On a split receptacle the tie bar is removed on the hot side (brass) of the receptacle but not on the neutral (silver) side. The red wire is connected to the top brass screw, the black wire is connected to the bottom brass screw and the white (neutral) wire is connected to the other side of the receptacle The rating of the breaker in the panel will be, 2 pole 15 amp. What this gives you is 2 separate 120 volt 15 amp circuits on one receptacle If the voltage was measured between the two hot slots on the right side of the receptacle top and bottom you would measure 240 volts. This voltage would only be 240 if the breaker feeding the receptacle was full size 2 pole and not mini breakers.
Can a 240 volt receptacle go on a 15 amp circut breaker?
In North America you would need two 15 amp breakers to obtain 240 volts. The wire for a 15 amp circuit would be #14 AWG. So to answer the question, yes a 240 volt receptacle can go on a 15 amp circuit.
The purpose of the SEC's circuit breakers rule is to?
The purpose of the SEC's circuit breakers rule is to:
Is a circuit breaker an alternative fuses?
Circuit breakers do the same thing as fuses. They interrupt current flow when a certain preset point is reached. The difference between circuit breakers and fuses are that circuit breakers are resettable and reusable, whereas fuses are one time devices that must be replaced after they blow.
Where can Square D circuit breakers be purchased?
Square D circuit breakers can be purchased from various homeware and DIY stores such as Home Depot or Lowes. Websites that specialise in circuit breakers such as Circuit Breaker Service or All Breakers do sell them as well.
Where are the circuit breakers on a 2000 chev Tahoe?
most circuit breakers are under the hood near the battery. major breakers. you have to unscrew cover.
What breakers are compatible with ge breaker boxes?
GE circuit breakers with catalog numbers ranging from THQL1115 through to THQL1150 can be substituted like for like with Cutler-Hammer circuit breakers coded CL115 through to CL150, ITE Siemens circuit breakers coded Q115 through to Q150 and Square D circuit breakers coded HOM115 through to HOM150. These are single pole breakers. GE circuit breakers with catalog codes from THQL2115 through to THQL2150 can be substituted with Cutler-Hammer circuit breakers CL215 through to CL250, Square D circuit breakers HOM215 through to HOM250 and ITE Siemens circuit breakers Q215 through to Q250 of the same amperage and voltage. These are double pole breakers.
Why won't the receptacle reset?
Check your circuit breaker. The receptacle may be malfunctioning or you may be overloading the circuit when trying to do the reset.
Is gold used in circuit breakers?
Certainly not in the case of high-voltage circuit breakers. Probably not in low-voltage circuit breakers, as copper is a better conductor and has a higher melting point.
3 pole circuit breakers?
3 pole circuit breakers are used for 3 phase lines
