0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How we decide the rating and requirement of CBCT?
Generally we use CBCT for earth fault/earth leakage relay tripping. Since the CBCT is going to provide on neutral side, first we have to find the full load current. If the full load current is 500A we have to use 100A/5A (ie 1/5th of full load current) CBCT. arunarafa@gmail.com
Is a relay defect and open load the same?
A relay is basically a controllable switch that connects a supply voltage to a load. If the relay is switch such that the load is not connected, that could be considered an open load. If it is switched the other way the load will be connected to its supply voltage. A defect in a relay would be something that caused it not to function correctly. It could be in the switch portion of the supply portion of the relay. Hence you are referring to different things and a defect may or may not cause the load to be open.
How do you test a solid state relay?
A small light bulb is often used to test a solid state relay (SSR). That is because a SSR needs a minimum load of at least 0.1 amps in order to operate. Using a meter does not provide a sufficient load.
What is thermal overload?
The load current is made to flow through the thermal overload relay, which is actually a bimetalic strip. Beyond a prespecified current the bimetalic strip tend to deflect due to heat (thermal effect) thus cutting off the circuit and hence it acts as an over load relay protection.
Vector diagram for a loaded transformer where the load is resistive?
the ampere i=0is theonlyedge where the e0b and e0c can come together and share the load and that way the two vector diagrams will connected and the load will be less resistive and more on the ek0 and c73 resistive load. the 38f93 relay will be the one to break the load 2u3 and e0b and e0c into diffrent components that will be drawn in the diagram.
How we decide the rating and requirement of CBCT?
Generally we use CBCT for earth fault/earth leakage relay tripping. Since the CBCT is going to provide on neutral side, first we have to find the full load current. If the full load current is 500A we have to use 100A/5A (ie 1/5th of full load current) CBCT. arunarafa@gmail.com
What is the difference between an earth fault relay and an over current relay?
earth fault relay is also a type of over current relay but the set value of current or relay sensing current is much less than the maximum load current.in over current relay relay sensing current ise than maximum load current mor
Is a relay considered a load?
The relay's coil(s) would be a load, but the main function of a relay is to act as a switch to control power to a larger load.
Is a relay defect and open load the same?
A relay is basically a controllable switch that connects a supply voltage to a load. If the relay is switch such that the load is not connected, that could be considered an open load. If it is switched the other way the load will be connected to its supply voltage. A defect in a relay would be something that caused it not to function correctly. It could be in the switch portion of the supply portion of the relay. Hence you are referring to different things and a defect may or may not cause the load to be open.
What do you mean by leakage reactance in a single phase transformer?
The leakage reactance is one of the components of the reactance in the input impedance that is there when the load impedance is purely resistive. The leakage reactance is due to flux that fails to link both the primary and the secondary windings.
What happen if you connect earth wire in place of neutral wire?
If there's no earth leakage protection unit in your main Distribution Board then the device will operate normally since the neutral and earth conductors are one on the supply side. But if there's Earth Leakage then because of the imbalance in the currents flowing through the Earth Leakage it will trap. What is called 'earth wire' in Europe is called 'ground' in the US and is often bare. Using a bare conductor as a neutral exposes you to potential shock. If the bare wire is properly connected at the panel, all is fine. But if you touch this bare neutral and provide a better grounding connection than the panel provides, you become part of the circuit to whatever device that circuit supplies. What is often missed in this scenario is that with the neutral being after the load, the load limits the current and your shock WILL NOT TRIP THE BREAKER.
What is working principle of relay?
That a small amount of power can control a larger load, or can switch an entirely separate load.
What happens if you energize power to wire on n.c. contacts?
If the relay contacts are in series with a connected load, then the load will energize.
What pulls power from a battery?
Any load connected to the battery like lights, fans etc. Apart from this there is leakage to the atmosphere and the environment. Though small this leakage over a long time will make a battery dead
What is different thermal over load relay and thermally protected?
no difference
Where is the load reduction relay 2003 vw jetta?
under the dashboard..
WHAT IS THE POSITIVE STUD AND NEGATIVE STUD OF A GLOW RELAY 12496472?
A typical automotive relay has numbered connections. Connection number 30 is the fused power supply to feed the load. In this case the load would be the glow plug(s). Number 87 is the load to the glow plug(s). Number 86 is the power supply that operates the relay, usually comes from an ignition or accessory switch. Number 85 provides the ground for the relay to operate.
