0
Does the neutral wire go on the silver screw when wiring switches or outlets?
Wiki User
∙ 14y ago
No, the switch just breaks the hot side of the circuit. The incoming hot wire should be connected to the top screw and the load side of the switch should be connected to the bottom screw. The neutral wire is usually connected together with a wire nut and pushed to the back of the switch box.
Wiki User
∙ 14y ago
Wiki User
∙ 11y agoWhite (neutral), in the USA.
The international standard color for the neutral wire insulation is blue.
Add your answer:
Earn +20 pts
The abbreviations COALR stands for?
Copper Aluminum Revised. These letters will appear on switches and electrical outlets where Aluminum wiring has been installed.
Can you add outlets to old knob and tube wiring?
Yes, but keep in mind Knob and tube generally switches the neutral wire instead of the "Hot". You can strip back the insulation about an inch and solder your new wire in place. If you've never done it before you might want to consult an Electrician. It can be tricky.
Electrical Wiring Installation?
form_title=Electrical Wiring Installation form_header=8293 How would you best describe your electrical project?*= () "Electrical panel upgrade only () Update or add a few fixtures, outlets or switches () Complete wiring for addition or remodel" Please describe this location.*= () Home/Residence () Business
If a 1950 era house has 10 gauge wiring for lights and outlets can you safely extend wiring with 12-2 for additional lights and outlets?
You can provided the protecting breaker for the circuit is 20 Amps or less.
Is conduit required for basement electrical outlets?
Conduit is not required for residential electrical IF THE WIRING IS BEHIND THE WALL. If it's exposed wiring, you'll need to use conduit.
The abbreviations COALR stands for?
Copper Aluminum Revised. These letters will appear on switches and electrical outlets where Aluminum wiring has been installed.
Can you add outlets to old knob and tube wiring?
Yes, but keep in mind Knob and tube generally switches the neutral wire instead of the "Hot". You can strip back the insulation about an inch and solder your new wire in place. If you've never done it before you might want to consult an Electrician. It can be tricky.
What does the noncurrent-carrying wiring devices industry make?
Popular products include electrical conduits and fittings, boxes for outlets, switches, and fuses, and pole and transmission line devices
Electrical Wiring Installation?
form_title=Electrical Wiring Installation form_header=8293 How would you best describe your electrical project?*= () "Electrical panel upgrade only () Update or add a few fixtures, outlets or switches () Complete wiring for addition or remodel" Please describe this location.*= () Home/Residence () Business
Outlets and Switches?
CHANGING OUTLETS AND SWITCHES IN A ROOMDon't let changing outlets and switches interfere with a room's decor and appearance.In order to meet certain standards and housing codes, rooms must have outlets and switches to allow wall-switch controlled lighting systems. When changing switches and outlets, home designers commonly use push button light switches, dimmer switches, modern toggle switches, outlets and even plug-in receptacles for portable lamps. Changing Outlets and Switches Can Get TrickyWiring is one of the most important things that need to be done when changing a switch or outlet in a room. Each room must meet housing codes to pass inspection; if installing a new outlet, seek professional guidance. There are many different ways to set up a switch with electrical wiring. Some examples include three-way switch wiring, four-way switch wiring, or outlet plug half switched wiring.The Basic Wiring Technique: Three-way Switch Wiring MethodFirst, remove the current switch panel that you are replacing. Once you have that completed, you will need a black electrical wire, black electrical tape, and a white electrical wire. The two wires will balance each other out. The wires should be attached to the fixture and the fuse box. The black wire is the wire that's live (or hot). This is called the ungrounded conductor. The white wire is known as the grounded conductor, which helps to prevent fires. Wrap the black electrical tape around the ends of the white wire. The reason for this is to secure the attachment, and also the tape acts as another ungrounded conductor.If you run into bare and green wires, don't panic. Those wires are supposed to be there. They act as equipment grounding conductors just as the white wire does. The bare and green wires can be used in replacement of the white wire, if the box is metallic.Check your work thoroughly and make sure you write down every step that you take, in detail. If you are not comfortable with changing outlets and switches then call a professional so they can do it for you.
How do you get the wiring out of your handlebars?
disconnect from switches and pull them out!
House Electrical Wiring?
form_title=house electrical wiring form_header=8283 Which areas of the home are to be included in this project?*= [] "Kitchen [] Bathroom(s) [] Bedroom(s) [] Living, Family, or Dining rooms [] Office [] Laundry or utility room [] Garage or Basement [] Patio or outdoors [] Other" Which types of electrical devices and/or appliances will you need wired?*= [] Switches (standard) [] Wall outlets [] Floor outlets [] Dedicated circuits [] Surge protection [] Doorbell [] Telephone/modem line [] Lightning protection [] Specialty lighting [] Ceiling fixtures/fans [] Attic/Whole house fans [] Spa [] Other How would you best describe your electrical project?*= () "Complete wiring for addition or remodel () Electrical panel upgrade only () Update or add a few fixtures, outlets or switches"
Does the circuit box have one side for neutral and the other side for ground?
No, a circuit box is just a metal or plastic box that encloses the wiring and has means for mounting a cover plate. Most circuit boxes are for mounting outlets or switches, but one type (also called the junction box) is only intended as a junction point for wiring for multiple circuits and its cover plate is solid (no openings).The wires that pass through a circuit box (usually together in a common plastic jacket) will be identified as:hot - black (220VAC service opposite phase hot - red)neutral - whiteground - green
What is different between electronics and electrical?
Electronics involves the behaviors of various components and their interactions to make a desired device or system (e.g. radio, TV, computer...).Electrical involves just power wiring, switches, outlets, lighting, etc.
If a 1950 era house has 10 gauge wiring for lights and outlets can you safely extend wiring with 12-2 for additional lights and outlets?
You can provided the protecting breaker for the circuit is 20 Amps or less.
I am trying to turn 1 light with 2 switches and i don't know how to give it powerelectricity?
This requires 3-way switches that have three separate terminals (plus ground). The method of wiring depends on where the light fixture is in relation to the switches and the feed wires. Most brands of switches contain wiring diagrams to help the installation.
Just discovered your house has aluminum wiring and you changed all the outlets to new white is there immediate danger?
If they're not CO/ALR outlets, there is.
